ptune Posted April 22, 2021 Report Share Posted April 22, 2021 Do anyone has a wire diagram for Evo 9 E-Throttle with Bosch Throttlebody and Evo X Pedal. Thank you Quote Link to comment Share on other sites More sharing options...
ptune Posted April 24, 2021 Author Report Share Posted April 24, 2021 Do anyone know where to get support from Links? Quote Link to comment Share on other sites More sharing options...
Adamw Posted April 25, 2021 Report Share Posted April 25, 2021 What throttle body do you have? For the pedal pinout you will have to find an EvoX wiring diagram. Quote Link to comment Share on other sites More sharing options...
ptune Posted April 26, 2021 Author Report Share Posted April 26, 2021 Hi Adam i had the Bosch 82mm Electronic Throttle Body. Evo X pedal pin out as follow : pin1 : +5V pin2: Sensor Ground pin3 : APS (Main) pin4 : +5V pin5 : Sensor Ground pin6 : APS (Sub) connected to Expansion connector 1: As Follow diagram provided by links top down order: PIN 2,5 = Gnd Pin 1,4 = +5V Pin 3 = Volt 11 Pin 6 = Volt 8 Bosch Throttle Body Pin out as follow: Pin 1 : Motor (-) Pin 2 : TPS(-) Pin 3 : TPS (+) Pin 4 : Motor (+) Pin 5 : TPS2 ( OUT ) Pin 6 : TPS1 (OUT ) Connected to Expansion Connector 2: As Follow diagram provided by links top down order: Pin 2 : Gnd Pin 3 : +5V Pin 4 : AUX 9 Pin 1 : AUX 10 Pin 5 : Volt 6 Pin 6 : Volt 7 Quote Link to comment Share on other sites More sharing options...
Adamw Posted April 26, 2021 Report Share Posted April 26, 2021 Yep looks correct Quote Link to comment Share on other sites More sharing options...
ptune Posted April 26, 2021 Author Report Share Posted April 26, 2021 Everything was wired but the throttle does not move as the pedal was depress, APS value moved and learn. TPS does not learn and give error msg, tps main not working. Swap pin 5 and & pin 6 around still getting the same tps main error. What would be the problem? Thank you. Quote Link to comment Share on other sites More sharing options...
Adamw Posted April 26, 2021 Report Share Posted April 26, 2021 Please attach your tune and a short log of the TP calibration attempt. Quote Link to comment Share on other sites More sharing options...
ptune Posted April 27, 2021 Author Report Share Posted April 27, 2021 Attach files and pictures test2.pclr Log 2021-04-27 5_35_32 pm.llg Quote Link to comment Share on other sites More sharing options...
Confused Posted April 27, 2021 Report Share Posted April 27, 2021 You have no PID, your min/max clamp settings look wrong, your E-Throttle target table is mostly full of 0s, and your log has almost no data in it. In future, please always provide a PC Log with every parameter added - what you think is relevant is often not actually relevant, and it's parameters you didn't log which can tell the rest of the story. I suggest you have a good read of the Help file, and fill in this missing data, and you may find that it begins to function a bit better. Adamw 1 Quote Link to comment Share on other sites More sharing options...
ptune Posted April 28, 2021 Author Report Share Posted April 28, 2021 Have enter all the needed valve as stated by Confused, can please help check what really goes wrong here. Still couldnt get the throttle to learn , same error TP ( Main ) no activity. File attach below, thank you. test1.llg Quote Link to comment Share on other sites More sharing options...
Adamw Posted April 28, 2021 Report Share Posted April 28, 2021 Can you attach the tune file as well. Aux 4 should be assigned to E-throttle signal 1. Also set active tables to 1. Do another log after making these changes. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.