superstockneo Posted May 11, 2022 Report Share Posted May 11, 2022 I’ve recently gotten the LinkEcu version of the cangauge. I’ve wired it up correctly with the gauge sitting at the end of the bus with the terminator in place. In between the bus is a line connected to my instrument cluster which relies on 500k bitrate. (Previously my cluster sits at the end of the bus, directly wired to the ecu canbus CAN2) I cannot get either to work with the included instructions settings (transmit generic dash on channelX, ID56). Is there any way to change the gauge to accept 500k? When the gauge is connected and powered on, my cluster stops working. When I unplug the gauge, my cluster comes back to life. I’ve also tried removing the terminating resistor on the gauge, it still won’t work and my cluster also won’t work as long as the gauge is powered on and connected. Ecu is furyX. Currently using CAN2. Easy way would just be purchasing a ltw to dash connector and use CAN1 but I’m trying to avoid that for now. Quote Link to comment Share on other sites More sharing options...
Adamw Posted May 11, 2022 Report Share Posted May 11, 2022 The gauge currently only supports 1Mbit. All devices on the same bus need to run at the same bit rate, so really moving to CAN 1 is the only option at present. Quote Link to comment Share on other sites More sharing options...
superstockneo Posted May 14, 2022 Author Report Share Posted May 14, 2022 Thanks Adam. Contacted gaugeart support. Although the gauge can be set at 500k, it's only available through the android app. But ideally they suggested that the gauge should run at 1mb and separate from the oem bus. So went ahead and bought a link candash cable instead. working well now. Question, transmit generic dash does transmit gear position from the help file but it doesn't seem to be displaying on the gauge. Is there any additional setting to it? Quote Link to comment Share on other sites More sharing options...
Vaughan Posted May 15, 2022 Report Share Posted May 15, 2022 On 5/15/2022 at 4:37 AM, raediyusof said: Question, transmit generic dash does transmit gear position from the help file but it doesn't seem to be displaying on the gauge. Is there any additional setting to it? Are your gears showing up correctly in the ECU? The setup for gear detection is in Chassis and Body -> Gear Detection Quote Link to comment Share on other sites More sharing options...
superstockneo Posted May 16, 2022 Author Report Share Posted May 16, 2022 5 hours ago, Vaughan said: Are your gears showing up correctly in the ECU? The setup for gear detection is in Chassis and Body -> Gear Detection Yes I've them set up and already have them running quite some time. Using the calculated method. Quote Link to comment Share on other sites More sharing options...
Vaughan Posted May 16, 2022 Report Share Posted May 16, 2022 If they are working in the ECU and the rest of the info in the CAN gauge I would expect them to work on the CAN gauge. I can test this later when I have a gauge handy. Quote Link to comment Share on other sites More sharing options...
Vaughan Posted June 20, 2022 Report Share Posted June 20, 2022 On 5/15/2022 at 4:37 AM, raediyusof said: Question, transmit generic dash does transmit gear position from the help file but it doesn't seem to be displaying on the gauge. Is there any additional setting to it? looks like this was an issue in the gauge software and it appears to have been fixed in the latest update. Quote Link to comment Share on other sites More sharing options...
superstockneo Posted June 20, 2022 Author Report Share Posted June 20, 2022 1 hour ago, Vaughan said: looks like this was an issue in the gauge software and it appears to have been fixed in the latest update. Thanks Vaughan. Do you mean the mobile app (ios/android)? I’m on ios. The app is a bit basic I don’t see options to upgrade the firmware etc. for the gauge. Quote Link to comment Share on other sites More sharing options...
Vaughan Posted June 20, 2022 Report Share Posted June 20, 2022 3 minutes ago, raediyusof said: Thanks Vaughan. Do you mean the mobile app (ios/android)? I’m on ios. The app is a bit basic I don’t see options to upgrade the firmware etc. for the gauge. Yes the mobile app, I'm on Android and it is V2.1.7. Maybe give it a week or two if you can't see an IOS update yet. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.