Jump to content

Recommended Posts

Posted

I have a Supralink with a Ford IACV  2-wire installed. Trying to get the idle dialed in. Has anyone done this or have any settings available?. Basically i have switched 12v to Pin1 and Aux6 wired to Pin2. ISC Solenoid assigned. Unsure of the rest of the specs and frequency. Just seeing if anyone has made this happen and if so this would be great info for the next guy. So far car idle climbs from 1k to 3k RPM as engine warms up. Here are a few specs. Thanks in advance.

 

image.thumb.png.320cb466cc86aa448e68d3046a168530.pngimage.thumb.png.86027f8e8656ffe75447bb36d470ab4c.pngimage.thumb.png.33cf0abbf7f0976759ab7d2d7b67bbf5.pngimage.thumb.png.664fee1bac6c8dcff2a27f6c2fbef8e3.png
 

Posted

Most of it looks ballpark ok.  The main setting that is not correct is the frequency on Aux 6, most ford valves like about 120Hz.

Posted

Excellent thank you. That value makes a huge difference. Internet list everything from 100Hz to 350Hz, hard to get a definitive answer on the Ford valves. I started at the 200Hz per the Link Open loop help file, worked my way up to 300Hz and back down to 153Hz. Ill try 120Hz. Very sensitive idle but getting close i think. Pretty much just spending hrs adjusting the Base Table but will report back with working settings once achieved. 

  • 1 year later...
Posted
On 6/18/2018 at 6:35 AM, driftninja said:

Excellent thank you. That value makes a huge difference. Internet list everything from 100Hz to 350Hz, hard to get a definitive answer on the Ford valves. I started at the 200Hz per the Link Open loop help file, worked my way up to 300Hz and back down to 153Hz. Ill try 120Hz. Very sensitive idle but getting close i think. Pretty much just spending hrs adjusting the Base Table but will report back with working settings once achieved. 

Sorry for bringing up an old thread, but im about to install the PHR kit soon and was wondering what settings you ended up using, and how well it works?
Any tips while installing?

Thank you

Posted

I’ll see if I can get you the info you need this evening. My car is not local at the moment but I think I saved a snip in my computer. The valve works awesome. I would use it over and over. You only need lik 2 wires out of that OEM harness and it frees up like 3 outputs. Not hard to dial in the idle table either. 

@Reemen

Posted
2 minutes ago, driftninja said:

I’ll see if I can get you the info you need this evening. My car is not local at the moment but I think I saved a snip in my computer. The valve works awesome. I would use it over and over. You only need lik 2 wires out of that OEM harness and it frees up like 3 outputs. Not hard to dial in the idle table either. 

@Reemen

That was a fast reply :wub:
That would be awsome!
I'm looking forward to installing it. I'm tired of having to sit on the throttle for like 10 minutes to get the engine warm before it manages to idle by itself

@driftninja

Posted

@Reemen ya this works flawlessly. Will high idle at startup to what ever you want, then it will adjust with AC, PS, and cooling fans. Simple. If I cannot find the info saved I can walk you through it too. 

Posted
1 hour ago, driftninja said:

@Reemen ya this works flawlessly. Will high idle at startup to what ever you want, then it will adjust with AC, PS, and cooling fans. Simple. If I cannot find the info saved I can walk you through it too. 

That would be great! i copied your settings that you posted above here as a base point. Its going to be 1-2 weeks before i can install it though.

  • 1 month later...
Posted

@driftninja

Hi again, so i have installed the valve and it works okay. 
I was just wondering if you ever had any problems with it staying open everytime you press the throttle?

Everytime i press the throttle when driving the valve opens, but if im above approx 2000rpm it shuts immidiatly, but if im below it stays open until i reach 2000rpm.
Its really annoying :blink:

  • 3 years later...
Posted

@driftninja @reemen Can either of you update this post to include final settings for Supralink with 2 wire PHR Ford IAC. Thanks.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...