Jump to content

Shedley

Dealer
  • Content Count

    73
  • Joined

  • Last visited

  • Days Won

    3

Everything posted by Shedley

  1. What I should do personally is: set load equation to map. Then set fuel table 1 to load axis tps, and map the car on waste gate pressure. Then ad boost and set up an 4d map with load axis map, to take the fine tunings in account were the map calculation does not fix the complete calculation. To have nice and steady afr's. Ditch that fuel map 2 and set up your lambda target table to map VS rpm, problem solved, you can make the afr leaner on low load(map) conditiond
  2. Shedley

    3sgte

    aaw, my bad, i was trying to open the file in G4+, which obviously doesn't work, compare function is not possible in G4 software as far as i know, i'm sory
  3. Shedley

    3sgte

    You can use the compare map file, then the program will show you all the differences in red I tried to open your map, but i can't open the map for some reason
  4. Shedley

    3sgte

    I'll take a look later this evening
  5. Shedley

    3sgte

    It's quite hard to guess what's happening if we can't see it
  6. Shedley

    3sgte

    Then you can't actually know what's happening, is it a mixture problem, ignition ect, can't know without logs
  7. Shedley

    3sgte

    Just keep in mind that cams have a big impact on VE(volumetric efficiency) what is your lambda doing, do you use the same spark plugs/gaps, same coil ect?
  8. Have had that issu as well, put iff you set something as a wheels speed, it stops happening You can also reinstall older firmware, in the update firmware tab, choose a older firmware, and install it
  9. Shedley

    3sgte

    Any logs and pcl file?
  10. Isn't there a iat sensor in the maf stock
  11. You have both options, you can just use the oem wires and change calibration in the ecu. That's what I should do
  12. There's a really good explanation here on the forum from mapper, I should look if I can find it Here you go:
  13. Shedley

    Rotary switch

    Yes indeed, what brand Rotary switches do you prefer?
  14. I'll tell you something: I've more then 5 customers running on a fury ├ęcu on a s54 engine with dual vanos. Vanos always active, even on idle. Afr spot on, nice flat torque curve between 365-400 nm and 365-410 hp (some stock engines, some build with 302/296 cams ect) all on 1 fuel map strategy. Your vvt maps decide the position off your cams, so if load axis of vvt and fuel map are the same, there is definitely not a need for a second fuel map. As you have a m50 with a simply on-off vanos, thing getting even more straight forward. You're making it yourself way to hard. Have done m52b25tu engine ass well, on another ecu brand, same story. Make it yourself easy, ditch that second fuel map, let your vanos switch at a certain rpm (which you can easy test on the dyno) and if you choose to let it switch on a certain tp as well then set your load axis to tp as well of the fuel map, otherwise you make things complicate for yourself
  15. You can just run the thermostat out of an aux output wich becomes active at a sertain ECT You can control the pwm fans with a solid state ralay
  16. Why you activate a second fuel table when vanos activates, it always activates on the same point/condition, so I would not know why you need that second one...
  17. Shedley

    GFB boost controller

    I would connect the solenoid to the ecu as well, you have much more advanced control like that
  18. Shedley

    Rotary switch

    Another 06 Another question, doesn't the value interpolate between positions if the input value differs a bit for some reason, compared to the calibrated value?
  19. Shedley

    Rotary switch

    Never thought of doing this through a cal table, good point. Could be easier though if we could just select rotory switch as an an function followed by: numbers of positions, threshold and then a simple table to define each position
  20. Shedley

    Nos control

    There's nothing wrong with it, just you loose a table you could need for something else.
  21. Shedley

    Rotary switch

    Interested in full Rotary switch support as well, so we could alter for example traction control slip %, als setting ect without the need off VA
  22. Shedley

    Egt Antilag

    I think there should me more protection strategies integrated in the antilag function such as max egt to automatic switch off antilag when egt's get high. Also a minimum ect to enable could be Interesting. Max iat function as well Also, on DBW, you can't have 2 different throttle openings on different antilag modes, or am I wrong, should be handy as well
  23. Shedley

    Nos control

    Really think we should ad in a proper nos controlling feature, so we don't need to twitch with tables to set everything up
  24. Don't understand this, my manual says something different, that's why i'm a bit confused
×
×
  • Create New...