Pete_89t2 Posted September 30, 2021 Report Share Posted September 30, 2021 I purchased one of these GaugeArt CAN bus gauges for my FD RX7, which is running a Link G4+ Fury ECU. Problem I'm having is the gauge refuses to display some of the extended channel data GaugeArt claims it should, for example Lambda target. Tech support folks at GaugeArt has been telling me for months now that they have been working with Link to come up with an updated set of configuration instructions that should fix my problem, but they have not delivered yet. Was hoping maybe someone here has figured out a solution for this. I simply want to be able to set up a 2 parameter display screen that shows Lambda 1 (a standard channel) and Lambda Target (an extended channel) on the same page. When I try to do that according to the GaugeArt instructions, Lambda 1 displays properly, but I get a constant 0.000 for Lambda Target. Anyway, here's a link to the standard and extended channel list this gauge is supposed to support and display: https://gaugeart.com/instructions/gaugeart-can-gauge-supported-ecu-data-channels/supported-ecu-channels-vipec-link-g4/ And here is a link to the instructions GaugeArt provides its users for them to configure a Link G4+ to work with their CAN bus gauge: https://gaugeart.com/instructions/vi-pec-link-g4-ecu-setup/ I've followed those instructions to the letter, with one exception - Since I wired my CAN gauge to DI9/10 (CAN2 module), I substituted CAN2 module for CAN1 module in their instructions. The GaugeArt gauge seems to work fine that way otherwise, and I can configure it to display everything it should, EXCEPT for the following extended channels: Lambda Target Lambda Correction 1 Lambda Correction 2 Boost Target (kPa / PSIg) Thanks in advance! Quote Link to comment Share on other sites More sharing options...
Adamw Posted September 30, 2021 Report Share Posted September 30, 2021 Their instructions are wrong. Extended stream 1 should be on ID 50, and extended stream 2 should be on ID 51. Quote Link to comment Share on other sites More sharing options...
Pete_89t2 Posted September 30, 2021 Author Report Share Posted September 30, 2021 30 minutes ago, Adamw said: Their instructions are wrong. Extended stream 1 should be on ID 50, and extended stream 2 should be on ID 51. Thanks Adam. It looks like I had ID 50 for extended stream 1, but per GaugeArt's instuctions, I only had 2 channels setup (standard on ID 56, extended on ID 50 for both streams). How/where would I change extended stream 2 to ID 51 - would I just add a 3rd channel (currently OFF) under the "Mode" tab, and assign it to ID 51? Quote Link to comment Share on other sites More sharing options...
Adamw Posted September 30, 2021 Report Share Posted September 30, 2021 Quote Link to comment Share on other sites More sharing options...
Pete_89t2 Posted September 30, 2021 Author Report Share Posted September 30, 2021 Perfect, thanks again! Quote Link to comment Share on other sites More sharing options...
VegasAWD Posted October 25, 2021 Report Share Posted October 25, 2021 Adding onto this: Just installed my GaugeArt CAN gauge and the ethanol content is reading zero. Firmware for both the ecu and gauge are up-to-date. Ethanol content reads fine in link. Thank you. can.pclr Quote Link to comment Share on other sites More sharing options...
Adamw Posted October 25, 2021 Report Share Posted October 25, 2021 Try this one. can + extra stream.pclr Quote Link to comment Share on other sites More sharing options...
VegasAWD Posted October 26, 2021 Report Share Posted October 26, 2021 22 hours ago, Adamw said: Try this one. can + extra stream.pclr 166.25 kB · 5 downloads Unfortunately that one didn't work. Should I redo the can gauge configuration? Quote Link to comment Share on other sites More sharing options...
Adamw Posted October 26, 2021 Report Share Posted October 26, 2021 Sorry, looks like I missed the ID was set incorrectly too. Try this one. canextrastream2.pclr Quote Link to comment Share on other sites More sharing options...
VegasAWD Posted October 26, 2021 Report Share Posted October 26, 2021 11 hours ago, Adamw said: Sorry, looks like I missed the ID was set incorrectly too. Try this one. canextrastream2.pclr 166.25 kB · 18 downloads Worked! Thank you sir. Quote Link to comment Share on other sites More sharing options...
troyj Posted August 6, 2023 Report Share Posted August 6, 2023 i have the same problem my link can gauge the flex % wont work and the fuel temp and road speed Quote Link to comment Share on other sites More sharing options...
Adamw Posted August 6, 2023 Report Share Posted August 6, 2023 Attach a copy of your tune. Quote Link to comment Share on other sites More sharing options...
troyj Posted August 7, 2023 Report Share Posted August 7, 2023 this is it here thanks Try this.pclr Quote Link to comment Share on other sites More sharing options...
Adamw Posted August 7, 2023 Report Share Posted August 7, 2023 You dont even have the extra stream set up. Instructions are here: https://linkecu.com/documentation/Can Gauge Online Manual.pdf Quote Link to comment Share on other sites More sharing options...
troyj Posted August 8, 2023 Report Share Posted August 8, 2023 Yeah i couldn't find the 2 gauge art can files they not in the g4+ can folder so i copied the 2 files from the g4x can folder to the g4+ can folder now it works thanks. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.