freeline Posted August 29, 2015 Report Share Posted August 29, 2015 Hello,I am a new owner of link g4 storm ecu and I want to use Honda ignition coils for my Peugeot 206 rc ewj4s engine with throttle bodies.(it goes about 9500 rpm).I do not use a camshaft sensor and I can't put one.Do i need to use igniter for these coils or they have them inside?Do you have a better proposal for ignition coils with or without igniter in them?Sorry for my bad english.RegardsJim Quote Link to comment Share on other sites More sharing options...
Simon Posted August 31, 2015 Report Share Posted August 31, 2015 You can use those coils you will just need to wire as wasted spark using only ignition drives 1 and 2.They are a smart coils and will not require an external igniter.They also use a conventional dwell signal so no need to change the spark edge from falling. Quote Link to comment Share on other sites More sharing options...
freeline Posted August 31, 2015 Author Report Share Posted August 31, 2015 Thank you very much for your help!Jim Quote Link to comment Share on other sites More sharing options...
freeline Posted October 11, 2015 Author Report Share Posted October 11, 2015 Do you know if Honda s2000 and Honda Civic type-r EP3 ignition coils have the same specs and use a conventional dwell signal so no need to change the spark edge from falling too?RegardsJim Quote Link to comment Share on other sites More sharing options...
Dave Kriedeman Posted October 11, 2015 Report Share Posted October 11, 2015 Hi freeline,sorry I am unfamiliar with these coils and Simon is in China this week training Tuners.He is away for a week.RegardsDave. Quote Link to comment Share on other sites More sharing options...
freeline Posted October 11, 2015 Author Report Share Posted October 11, 2015 Thank you Dave,I will wait until Simon is back.RegardsJim Quote Link to comment Share on other sites More sharing options...
Simon Posted October 15, 2015 Report Share Posted October 15, 2015 Hello from China!The coils on the S2000 are conventional so require a falling spark edge. Quote Link to comment Share on other sites More sharing options...
freeline Posted October 15, 2015 Author Report Share Posted October 15, 2015 Hello Simon,I have Denso 099700-070 ignition coils and I am not sure if it needs falling spark edge or not.I bought them for Honda s2000 ignition coils and I dont know if they are the original ones.RegardsJim Quote Link to comment Share on other sites More sharing options...
freeline Posted October 15, 2015 Author Report Share Posted October 15, 2015 Sorry Simon,what do you mean falling spark edge? Quote Link to comment Share on other sites More sharing options...
Scott Posted October 16, 2015 Report Share Posted October 16, 2015 Hi Jim,According to what I can find out, the coils you have are used on k20a engines and have built in ignitors. When Simon says they require a falling spark edge he means set ECU Settings > Ignition > Ignition Setup > Ignition Main > Spark Edge to 'Falling'.Scott Quote Link to comment Share on other sites More sharing options...
freeline Posted October 16, 2015 Author Report Share Posted October 16, 2015 Thanks,do you know the wiring diagram of the coils?Jim Quote Link to comment Share on other sites More sharing options...
Scott Posted October 18, 2015 Report Share Posted October 18, 2015 Hi Jim,I don't have this information, I did however find a forum where someone wrote the pinout. I do not know if this is accurate.http://honda-tech.com/honda-s2000-5/s2000-cops-coil-pinout-diagram-needed-2276493/Scott Quote Link to comment Share on other sites More sharing options...
freeline Posted October 19, 2015 Author Report Share Posted October 19, 2015 Hi Scott,It is very helpfull and I am going to check it.Thanks a lot.Jim Quote Link to comment Share on other sites More sharing options...
Dadoulis Paschalis Posted January 4, 2016 Report Share Posted January 4, 2016 Everything is working ok now, I just keep getting an rpm limit activated message even if I completely turn rpm limit off.If I m helping car is starting ok and runs in idle but sounds like it is really reaches rpm limit although it reads 1650rpm maxAlso trigger error is around 6...If anyone can help I.would be thankfulThanks Quote Link to comment Share on other sites More sharing options...
Dave Kriedeman Posted January 5, 2016 Report Share Posted January 5, 2016 Hi ,can you please post your PCL file or PM me .RegardsDave. Quote Link to comment Share on other sites More sharing options...
Dadoulis Paschalis Posted January 5, 2016 Report Share Posted January 5, 2016 Hi ,can you please post your PCL file or PM me .RegardsDave.https://www.dropbox.com/s/p7nzx60pe4qx7r0/zx_last.pcl?dl=0 Thanks a lot Quote Link to comment Share on other sites More sharing options...
Dave Kriedeman Posted January 5, 2016 Report Share Posted January 5, 2016 Hi ,have downloaded your PCL FILE i will check over ASAP.regardsDave. Dadoulis Paschalis 1 Quote Link to comment Share on other sites More sharing options...
Dadoulis Paschalis Posted January 7, 2016 Report Share Posted January 7, 2016 Hi ,have downloaded your PCL FILE i will check over ASAP.regardsDave.HiHave you got any idea?? Quote Link to comment Share on other sites More sharing options...
Dave Kriedeman Posted January 8, 2016 Report Share Posted January 8, 2016 Hello,I have not had a look as yet but will do my best over the weekend.Sorry i am not well.RegardsDave. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.