PitBull Posted March 2, 2016 Report Share Posted March 2, 2016 When I have the MAP Limit set for a 2D table, values in the cells are displayed as either PSI or kPa (depending on the Units setting). However, when I switch it to a 3D table, I can only change the cell values in increments of 5 and the values displayed does not change regardless of whether or not I select Metric or Imperial, so I'm not exactly sure what the values in the cell are representing (PSI or kPa). Is something wrong with this?Regarding the MAP limit (status) parameter: I I know it can be either 0 or 1. But, does it go to 1 as soon as any amount of cut happens, or does it go to 1 when 100% cut is hit?Thank youPB Quote Link to comment Share on other sites More sharing options...
TechDave Posted March 2, 2016 Report Share Posted March 2, 2016 Ok, we fixed the thing.#TeamEngineering Quote Link to comment Share on other sites More sharing options...
PitBull Posted March 2, 2016 Author Report Share Posted March 2, 2016 Ah ok. Is the fix to the PC software or ECU firmware (or both?) and will it be available immediately or with the next update?Can you comment on my other question regarding the MAP limit (status) parameter?Thanks!PB Quote Link to comment Share on other sites More sharing options...
TechDave Posted March 2, 2016 Report Share Posted March 2, 2016 (edited) PCLink fix.The value in that cell will be in kPA, so you'll just need to convert your psi into kPA.I've asked Simon and/or Scott to jump in on your map limit question, I can't test it on the bench right now.edit: fix should be in the next release, pending testing approval. Edited March 2, 2016 by EngineeringDave Quote Link to comment Share on other sites More sharing options...
Scott Posted March 2, 2016 Report Share Posted March 2, 2016 Regarding the MAP limit (status) parameter: I I know it can be either 0 or 1. But, does it go to 1 as soon as any amount of cut happens, or does it go to 1 when 100% cut is hit?The MAP Limit Status will become active as soon as the MAP Limit becomes active. On the default settings this would be 10kPa below the MAP Limit value. So the actual percentage of cut has no effect on the status. Quote Link to comment Share on other sites More sharing options...
PitBull Posted March 3, 2016 Author Report Share Posted March 3, 2016 PCLink fix.The value in that cell will be in kPA, so you'll just need to convert your psi into kPA.I've asked Simon and/or Scott to jump in on your map limit question, I can't test it on the bench right now.edit: fix should be in the next release, pending testing approval.Could there be the possibility to change the limit value from kPa to psi when the units are set to Imperial? It's impossible to view a graph of MAP vs MAP limit values when one is in PSI and the other is in kPa. Thank youPB Quote Link to comment Share on other sites More sharing options...
TechDave Posted March 3, 2016 Report Share Posted March 3, 2016 Could there be the possibility to change the limit value from kPa to psi when the units are set to Imperial? It's impossible to view a graph of MAP vs MAP limit values when one is in PSI and the other is in kPa. Thank youPBYup, it'll be in the next release pending testing approval. Quote Link to comment Share on other sites More sharing options...
Scott Posted March 3, 2016 Report Share Posted March 3, 2016 (edited) The MAP Limit value should change to psi also, but does not. I will ask for this to be changed.The engineering team have confirmed this will be changed in our next major release. Edited March 3, 2016 by Scott Forum combined my posts. Quote Link to comment Share on other sites More sharing options...
PitBull Posted March 3, 2016 Author Report Share Posted March 3, 2016 Awesome...thanks!!! Quote Link to comment Share on other sites More sharing options...
PitBull Posted July 16, 2016 Author Report Share Posted July 16, 2016 (edited) Hello...Did this get fixed? I tried switching to a 3D MAP limit and it appears the MAP limit value in the cells are still displayed in kPa even when Units are set to ImperialThank you Edited July 16, 2016 by PitBull Quote Link to comment Share on other sites More sharing options...
PitBull Posted July 21, 2016 Author Report Share Posted July 21, 2016 Hello, any info on the status of this?Thanks Quote Link to comment Share on other sites More sharing options...
Rich RDE Posted July 21, 2016 Report Share Posted July 21, 2016 Hello, any info on the status of this?ThanksHi Pitbull,I am sure the engineering team is working on this. There have been a lot of updates and things that are constantly being updated. With all the new changes with branding and stuff. I am sure this will be resolved shortly. Sometimes not always as fast as we would like but it will get done. Hang in there. Quote Link to comment Share on other sites More sharing options...
Simon Posted July 21, 2016 Report Share Posted July 21, 2016 Yep they have been. It just missed the last update so will be in the next. Quote Link to comment Share on other sites More sharing options...
PitBull Posted July 22, 2016 Author Report Share Posted July 22, 2016 Thank you for the update. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.