theandydove Posted August 3, 2017 Report Share Posted August 3, 2017 Hi guys,I am wanting to change to a DBW throttle setup, is this possible on a GTR Link as I do not see it having Aux 9 & 10 available?Kind regardsAndy Quote Link to comment Share on other sites More sharing options...
Simon Posted August 3, 2017 Report Share Posted August 3, 2017 Not in a tidy fashion it would require wire links on the board. But ultimately could be done. Quote Link to comment Share on other sites More sharing options...
theandydove Posted August 4, 2017 Author Report Share Posted August 4, 2017 (edited) thanks Simon, I had actually eventually found that answer in another topic. I guess that's a case of sending it to NZ to be done? (i'm in the UK) Edited August 4, 2017 by theandydove Quote Link to comment Share on other sites More sharing options...
Simon Posted August 6, 2017 Report Share Posted August 6, 2017 From our end we prefer that. And it does then offer some warranty cover. But it can also be done remotely but no warranty. Quote Link to comment Share on other sites More sharing options...
AbbeyMS Posted August 25, 2017 Report Share Posted August 25, 2017 We went over to a Link Thunder to run DBW on a 32GTR bit now have an issue with no throttle output to the 4WD/ABS computer. Something we are looking into. If we could run DBW on a PnP GTR ECU that may have some help in making the change over to DBW easier. Quote Link to comment Share on other sites More sharing options...
Adamw Posted August 25, 2017 Report Share Posted August 25, 2017 It can be done. It would be best to request it at the time of order then it doesnt need to be shipped back to us for modification. Note if you contact tech support we will also give you the circuit required to get the TP out signal from the Thunder to make the GTR Attessa work. Steve 1 Quote Link to comment Share on other sites More sharing options...
BCNR33Zed Posted August 25, 2017 Report Share Posted August 25, 2017 Hi, Is possible to run DBW on a GTRLink? I'll want to run a DBW Setup on ITBs so I'm going to install a BMW M3 E46 DBW Actuator. Quote Link to comment Share on other sites More sharing options...
AbbeyMS Posted August 25, 2017 Report Share Posted August 25, 2017 It can be done. It would be best to request it at the time of order then it doesnt need to be shipped back to us for modification. Note if you contact tech support we will also give you the circuit required to get the TP out signal from the Thunder to make the GTR Attessa work.I did speak to Simon regards this during the week I will ask him again. Hi, Is possible to run DBW on a GTRLink? I'll want to run a DBW Setup on ITBs so I'm going to install a BMW M3 E46 DBW Actuator. I think the BMW Motor pulls to much load for the Link ECU DBW motor. Quote Link to comment Share on other sites More sharing options...
BCNR33Zed Posted August 25, 2017 Report Share Posted August 25, 2017 I think the BMW Motor pulls to much load for the Link ECU DBW motor.There are others motors that I can use for keep the OEM Multiplies Throttle Bodies? Quote Link to comment Share on other sites More sharing options...
Steve Posted August 25, 2017 Report Share Posted August 25, 2017 Whats the amplimit on link? 5 amps? Quote Link to comment Share on other sites More sharing options...
AbbeyMS Posted August 25, 2017 Report Share Posted August 25, 2017 The guys @ link said you can remove some springs from the BMW DBW motor to drop the load require but I just went for a Nissan 350Z TB and removed the ITB's. Quote Link to comment Share on other sites More sharing options...
Adamw Posted August 26, 2017 Report Share Posted August 26, 2017 Whats the amplimit on link? 5 amps?Around 4A continuous for Aux9/10. The guys @ link said you can remove some springs from the BMW DBW motor to drop the load require but I just went for a Nissan 350Z TB and removed the ITB's.We reports from a couple of users driving the S54 system reliably after removing 3 of the 7 springs. There is one spring on the motor & six on the ITBs. AbbeyMS 1 Quote Link to comment Share on other sites More sharing options...
BCNR33Zed Posted August 26, 2017 Report Share Posted August 26, 2017 How is possible to wire the DBW system in G4+ for GTR? Quote Link to comment Share on other sites More sharing options...
Adamw Posted August 26, 2017 Report Share Posted August 26, 2017 How is possible to wire the DBW system in G4+ for GTR?The ECU will need to come back to us for modification. Quote Link to comment Share on other sites More sharing options...
AbbeyMS Posted August 26, 2017 Report Share Posted August 26, 2017 Adam, we got the 4wd working with the Thunder pretty easily. we spliced the wire that connects to the 4wd ECU to one of the outputs from the throttle pedal outputs (0-5volt output)Would be good to your work around thou @ Link HQ Quote Link to comment Share on other sites More sharing options...
BCNR33Zed Posted August 27, 2017 Report Share Posted August 27, 2017 The ECU will need to come back to us for modification.i've send an email for more infos and prices.i'm waiting for the reply :) Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.