loockheed Posted October 17, 2017 Report Share Posted October 17, 2017 hi there I have just changed from side feed 740 nismo injectors to asnu 800 long nose injectors and have rough idle and stalling problems on a jdm forester sti 04 plate sg 9 I am completely new to ecu tuning and need to know if this is damaging my engine ,injectors ,or ecu ? I have just down loaded the relevant software so I can look in to it before I drive the 80 miles too the proper mapper . sorry for such a simple question and please answer in a way a child can understand and thanks in advance Quote Link to comment Share on other sites More sharing options...
Simon Posted October 17, 2017 Report Share Posted October 17, 2017 The increase in injector size will be causing it to be rich running. You will need to adjust injector data and the fuelling to compensate for the new injectors. If you post you map from the ECU we can advise the settings that will need to be corrected. Quote Link to comment Share on other sites More sharing options...
loockheed Posted October 17, 2017 Author Report Share Posted October 17, 2017 thank you very much its late here so ill try in the morning Quote Link to comment Share on other sites More sharing options...
loockheed Posted October 18, 2017 Author Report Share Posted October 18, 2017 Ok so I found fault code an t1 at 5v ! what does this mean? is this causing rough idle and stalling ? thanks Will Quote Link to comment Share on other sites More sharing options...
loockheed Posted October 18, 2017 Author Report Share Posted October 18, 2017 1 cleared ecu fault - idle returned to near normal 2 tested anti lag - idle reverted to rough 300/400 rpm wanting to stall. 3 check ecu faults, none found log attached to this post, any help and advice is appreciated. Is anyone in the UK, south coast that can teach me how to use the link G4+ ? Thanks Wil ECU Log 2017-10-18 11;39;14 am.llg Quote Link to comment Share on other sites More sharing options...
loockheed Posted October 18, 2017 Author Report Share Posted October 18, 2017 zipped 3 minute log, attached to this post ecu log3 min.zip Quote Link to comment Share on other sites More sharing options...
Adamw Posted October 18, 2017 Report Share Posted October 18, 2017 Simon asked for a map earlier, can you attach that please. Quote Link to comment Share on other sites More sharing options...
Ducie54 Posted October 18, 2017 Report Share Posted October 18, 2017 11 hours ago, loockheed said: 1 cleared ecu fault - idle returned to near normal 2 tested anti lag - idle reverted to rough 300/400 rpm wanting to stall. What motor and does it have hydraulic lifters. Being new to tuning I would get the basics right first before playing with motorsport features Quote Link to comment Share on other sites More sharing options...
loockheed Posted October 23, 2017 Author Report Share Posted October 23, 2017 Hi my car has solid lifters (shimless) I'm just struggling with how to find and send the map , the engine is an ej 22 stroked to 2.35 . I only turned on anti lag because it seamed to reset the idle before I changed the manifold and injectors , there doesn't seam to be any air leaks that may cause rough idle again sorry for such simple questions and yes it does seam to be running rich as exhaust reeks of fuel Quote Link to comment Share on other sites More sharing options...
loockheed Posted October 23, 2017 Author Report Share Posted October 23, 2017 here is the mixture map screen shot and the fuel table. If this is not what is being asked for please explain in detail what is required and how to download it. I'm struggling with the g4+ operating system, for example how do you download the map ? . forester.pclr Quote Link to comment Share on other sites More sharing options...
AbbeyMS Posted October 23, 2017 Report Share Posted October 23, 2017 Have you inputted the new injectors battery offsets numbers? Quote Link to comment Share on other sites More sharing options...
Adamw Posted October 24, 2017 Report Share Posted October 24, 2017 Most likely you will just need to reduce your "master Fuel" number a little. Yours is presently set at 12ms, since your injectors are about 8% bigger then reducing this number to 11 should reduce the pulse width by about 8% and get you in the ball park. You may even need to drop it a little further but try it and see. Also once you actually get to the tuner, please suggest to them that they do a firmware update before they tune - yours is very old and there have been many fixes and improvements since. Quote Link to comment Share on other sites More sharing options...
loockheed Posted October 27, 2017 Author Report Share Posted October 27, 2017 thanks adam I have done that , is there anything I can do to stop the motor stalling it seams like its hunting from 300 rpm to 1200 rpm when enrichment has finished . it does this for about 15 to 20 seconds and then stalls . Quote Link to comment Share on other sites More sharing options...
loockheed Posted October 27, 2017 Author Report Share Posted October 27, 2017 On 23/10/2017 at 10:52 PM, AbbeyMS said: Have you inputted the new injectors battery offsets numbers? hi mark I have recently been to yours for geometry and dealt with scott , is changing injector b offsets something I should do ,as I am a complete novice ? Quote Link to comment Share on other sites More sharing options...
Adamw Posted October 27, 2017 Report Share Posted October 27, 2017 8 hours ago, loockheed said: thanks adam I have done that , is there anything I can do to stop the motor stalling it seams like its hunting from 300 rpm to 1200 rpm when enrichment has finished . it does this for about 15 to 20 seconds and then stalls . If you post a log and map we might be able to improve it https://www.youtube.com/watch?v=_P1LRANeO4A, but in your earlier logs your lambda is not working so without that we havent got much to work with. Originally you said you just needed to get it running good enough to take it to the tuner, is it still not driveable? Quote Link to comment Share on other sites More sharing options...
AbbeyMS Posted October 30, 2017 Report Share Posted October 30, 2017 On 27/10/2017 at 10:12 PM, loockheed said: Send me a PM with a contact number I will endeavour to help you out TechDave 1 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.