Adamw Posted December 15, 2019 Report Share Posted December 15, 2019 9 hours ago, M.D. said: The other fault (picture won’t upload) is.... ecu fault code 72: analog 5v supply error e throttle ecu fault code 73: aux 9/10 supply error ecu fault code 74: analog 5v supply error For some reason I have the faults separately but usually all these faults come up at the same time when it limits the throttle. But as I say we managed to stop a lot of these faults by changing the 0-5v figures. Just unfortunately you can’t use anti lag or launch control as the error will come up again I have asked directly before and was told it’s not something link have had before. And never got anymore from it. was just replying as the guy above has the same an12 as I’ve had. the stock 350z does have an air temp sensor. It’s within the stock AFM and set up as such on the pc link software under sensor type. Error 72 & 74 suggests you have a wiring problem somewhere. This is causing your E-throttle problems - it is not a "overly sensitive throttle" that is causing your problem. Please start your own thread and attach a log and your tune. Quote Link to comment Share on other sites More sharing options...
M.D. Posted December 15, 2019 Report Share Posted December 15, 2019 I will do when I get chance. the car has never had any wiring issues in the past though. And ran perfectly for 12 years on the stock ecu. Quote Link to comment Share on other sites More sharing options...
andybp Posted December 15, 2019 Report Share Posted December 15, 2019 i had similar issues with my 350z when i was using a modified 350z throttle body to operate my ITB's basically it was too much load on the motor when I went back to a standard throttle body for a while still using the link ecu the problems stopped i now have a cable setup Quote Link to comment Share on other sites More sharing options...
skeruno Posted February 1, 2020 Report Share Posted February 1, 2020 @Adamw Do you have the information to get the ABS going on my 350Z? Kind regards, Vincent Quote Link to comment Share on other sites More sharing options...
RobPhoboS Posted August 19, 2022 Report Share Posted August 19, 2022 @Adamw Possible to also PM me the details for the issue with VDC and SLIP light always on? Many thanks ! Quote Link to comment Share on other sites More sharing options...
BeallJK Posted August 19, 2022 Report Share Posted August 19, 2022 1 hour ago, RobPhoboS said: @Adamw Possible to also PM me the details for the issue with VDC and SLIP light always on? Many thanks ! I believe the solution is to put a 5pin relay in the ignition circuit: Is it this?? If it is, send Adam thanks bc he’s the one that helped me! RobPhoboS 1 Quote Link to comment Share on other sites More sharing options...
skeruno Posted August 19, 2022 Report Share Posted August 19, 2022 2 hours ago, RobPhoboS said: @Adamw Possible to also PM me the details for the issue with VDC and SLIP light always on? Many thanks ! The fix for me(thanks to Adam's input) was to start the ABS computer a bit later. This can be done by adding a relay between te power wire of the ABS computer and let the ECU switch the relay so that the ABS computer gets power cycled. Hope this helps. Kind regards, Vincent RobPhoboS 1 Quote Link to comment Share on other sites More sharing options...
Adamw Posted August 19, 2022 Report Share Posted August 19, 2022 8 hours ago, RobPhoboS said: Possible to also PM me the details for the issue with VDC and SLIP light always on? First of all do you have a G4+? We havent sold them for a few years and the G4X doesnt cause this issue. Quote Link to comment Share on other sites More sharing options...
RobPhoboS Posted August 21, 2022 Report Share Posted August 21, 2022 On 8/19/2022 at 11:36 PM, Adamw said: First of all do you have a G4+? We havent sold them for a few years and the G4X doesnt cause this issue. Hey Adam, I have the Vipec i88 350z p&p (just running G4+ software). Quote Link to comment Share on other sites More sharing options...
Adamw Posted August 21, 2022 Report Share Posted August 21, 2022 Ok, havent sold those for even longer... I will send you a PM. RobPhoboS 1 Quote Link to comment Share on other sites More sharing options...
RobPhoboS Posted August 22, 2022 Report Share Posted August 22, 2022 10 hours ago, Adamw said: Ok, havent sold those for even longer... I will send you a PM. Probably since 2014 Cheers for the PM and replies guys Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.