tbase

@koracing Here is the setting. I also upload log file as well here, I think size is correct. https://we.tl/t-4C1pN6MDqg

it’s ECU log @Adamw It’s like this 2 out of 5 files when download at the time.

Sometime when I open the log file show up like this. What's the cause?

Dope, Thanks a lot @Adamw and @VtrSp1 , I have learn a lot about gear shift from your thread which is very helpful. Yeah, I think gear lever force log are too low at 50Hz. Let me try with 500Hz. Is there any possible to do Ignition trim during overrun downshift? Reason is during autoblip could make RPM up with less torque.

its Close loop bro. Shift end mode is barrel position. I just changed to G4X and I think they change “max shift time” to “cut period”. So not sure what to put coz When I put 500ms value (copy value from Max shift time) , its delay power resume after gear finish changing. And help file still show Max shift time when I click at cut period.

@adamw Pls take a look if anything I can tweak to make gearshift better? - Just wondering about the Cut time period, I put 100ms is it ok? - The more higher gear the more fast shift period time, is it normal like this? Any thing I can make lower gear faster?

@Adamw Does it has in G4X?

Setting should be about right but Gear Lever Force won't active. Any advice?

Throttle problem fixed, but Trigger set up still dont work.

I just switch from Fury to Fury-X. I have tried to export all table and setting from previous file as much as I think I can. But I found problems. 1) Car won't start 2) E-Throttle won't work. I have attached both old and new files, please give some advice with thanks. Files are too big so I upload via wetransfer https://we.tl/t-pUYmJn3dax

Problem solved. I have to create new file and upload. I think RS3 Beta version for PDM still not reliable and need improvement.

@Adamw Can we try to change Gear Position can channel to channel 49?

Here u go

@Adamw Please forget about the PDM analog input, I just tab signal cable from Gear position sensor that goes to ANVT1 to PDM analog 5 just to see to make it works but it never be the same as reading direct from ECU stream. Reading from PDM analog, voltage not stable and can't show N and R position as the sensor calibration can't input alphabet. Anyway, you ask me for Can config export from ECU or PDM? How to do so? I'm not quite sure how to export CAN config that you request. Is it this one? I just use steam2 "generic dash". Steam 1 is one that you made it for me a while ago.

My set up is Link fury with AIM PDM32, everything work just fine until last FW update from AIM which make its messy. Gear position are no more show. I have check Can stream channel are both CC13 but it doesnt show by somehow. Gear detection value on ANVolt in ECU works fine but its like AIM doesnt communicate it right. I attached both file, is it possible to move gear position on ECU can stream and create another channel to match with on AIM file? @Adamw File can't attached as its oversize so I upload thru wetransfer. https://we.tl/t-3QeV57sgie Thanks in advance for help

Yeah, its connected to Digital , 14V from ECU and GND. Cable are connected well. DI 5 has set up as Ethanol Sensor.

Not sure, how to figure out as Ethanol sensor keep show error.

Thanks @adamw One last thing is there is a big latency of display which is quite annoyed as the ECU rpm limit reach before display show. Anyway we can do about it?

Hi, I'm struggling on trying to some value that isn't on the basic preset on Link ECU stream in AIM RS3 in order to show on AIM dash. I'd like Gear box oil temp AT4 and Ethanol Sensor Content value and Temp to show. How can I set up both LINK and AIM File. I've attached .plcr and zconfig files here., please help with thanks @adamw

Finally solved problem Adam. Its about the ground wring something wrong with it. Thanks for your help

Mine goes to 4000 RPM so its not on LIMP mode, isn't it? I will recheck all the wiring again today. And about the E-Throttle relay 1 that should goes to AUX. What should it wire to PDM? Ground?

@adamw My set up is link with AIM PDM and AIM GPS08. Is it possible to use GPS Speed as Non Driven Speed? Can Fury steam this data from AIM?

@Adamw Sorry for digging this topic. What is it supposed to be set of Y Axis in this case?

@adamw What is the setting to make to ref limit when AP has gone off track? Now what there is error, REV goes up so I have to cut the engine every time.