lysaer

Hi all Car is running fine except when I turn on the A/C it drops revs and has a tendency to stall either while idle or coming to a stop any input would be greatly appreciated, I have attached a copy of my latest PCLR and can take a log if needed Thank in advance all r33_gtr_march_2018_oil_pressure_enabled.pclr

Hi there I am looking at setting up the traction control with my Link g4+ on my r33 gtr, I was wondering if I would need to wire each wheels ABS sensor to the ECU with an XS loom I currently also have Do-Luck DTM II installed, will that have any negative affect on the traction control from the ECU or will it work harmoniously Thanks in advance all

Will the ECU USB output enough ampage to charge the tablet while in use? A standard USB 2 port outputs 500ma and a USB 3 outputs 900ma, I would imagine the tablet to need about 1.2amps+ in order to charge it while the screen is on or the tablet is being used

Ahh ok So would I need a replacement sender installed ? I think I must have one because I think at one point it was working I think possibly it might be this one https://www.rhdjapan.com/hks-camp-2-i-f-option-parts-temperature-sensor.html Because when I had the camp 2 installed it definitely showed oil temperature Just an update, my engine builder said he think he put a defi sender in there, so what settings would I need for that please thanks in advance

Hi All I have a Gaugeart box hooked up to an LCD to show data from my ECU for my r33 GTR I have managed to get most sensors setup and working but for some reason I cannot get oil temperature to display, I am not sure if I need to enable it somewhere in the ECU or if it is enabled by default, since the r33 gtr comes with an analog display oil temp sensor originally installed in the dash I have an oil pressure sensor hooked up which is working fine. Have attached a copy of my PCLR Thanks in advance r33_gtr_march_2018_oil_pressure_enabled.pclr

Sorted, fuel pump fuse and holder have melted lol, so pump wasn't coming on

Could that be a bad hose from the rail to the fuel pressure regulator ?

For future reference if anyone else has this issue set function to LF wheel speed

Hi all Jumped in my car today to take it for a drive and the car has a seriously rough idle which then cuts out and when I try to rev the engine it struggles to get above 4k and just keeps backfiring. I pulled the plugs and they were pretty black so swapped for brand new ones but the foul within the first couple of starts and have the same issues. The car was running fine last time I drove it a week ago with no issues at all. I have attached a log file and my current map Thanks in advance Log 2017-11-24 2_10_11 pm.llg r33_latest_november_17.pclr

Cheers @Adamw will go and try that now!

Hi all How do I enable the wheelspeed over CAN out so that it displays on my gaugeart LCD All other sensors are showing fine, oil temp, oil pressure, water temp, boost, battery etc Thanks in advance

Ok great, so long as there is absolutely no possible chance it could interfere or slow down my CAN lambda in anyways then I will do that Thanks again

Hey all Currently on my CAN1 I have my lambda sensor which runs at 1mbit and on CAN2 I have my gaugeart, dash2pro and OBD2 port The problem I am having is that the gaugeart and dash2pro both run at 1mbit and the OBD2 at 500kb. If I set the CAN port to one or the other either the OBD2 doesn't work or the gaugeart/dash2pro doesn't work It is my understanding that having multiple devices on the CAN slows the speed down, I am therefore reluctant to put the gaugeart and dash2pro no the CAN1 as I want the lambda to be running as fast as possible without chance of slowdown. My question is, could I use a resistor or something to trick the OBD2 port to think it is only running at 500kb while I have the actual port set to 1Mbit to run the other devices ? Thanks in advance

Hi there Which sensors would be recommend plug and play to easily integrate with the link g4+ ecu for my rb26dett engine please Want to monitor all the main important information, oil pressure, water temp, egt, o2 etc etc I currently have the HKS camp 2 additional sensors, could they just be wired in ? https://www.nengun.com/hks/camp-2 Will I also need the XS expansion loom ? Would it also be worth fitting the Link igniter ? Thank you in advance

Thanks Adam I will look into this now

Cheers Simon Any info about being able to get a video stream from the Dash 2 to an RCA I have looked at the connections and cannot see a video out anywhere on my unit, so far my idea would be to use a OBD2 to usb into an android device running Torque, then output the android device hdmi to rca converter box then rca into the dash, unless you can recommend a simpler way

Excellent, thank you Simon. Do you know if I wired 2 obd2 ports they would both read the data equally to different devices ? Also, is there a video out on the Link ecu, I have the nismo lcd dash as attached picture, I also have purchased the Link dash which will be used mainly for race days and just attached to the steering column as and when needed. but for daily driving if i could feed the data to the video rca on the Nismo dash that would be great thank you in advance

Hi there I have just ordered my link g4+ plugin along with the dash and all the bells and whistles. The r33 gtr uses the Nissan consult cableandd I was just wondering if it would be possible to wire an obd2 port to the ecu in order to send telemetry via Bluetooth to the Torque android app