Ryan21 Posted February 14, 2021 Report Share Posted February 14, 2021 Does anyone have a k24 on a Link Monsoon? If so, could you post a picture or explain your installer I/O table? Thank you, Ryan Quote Link to comment Share on other sites More sharing options...
Adamw Posted February 14, 2021 Report Share Posted February 14, 2021 There is a K20 Monsoon basemap in PC link, that will be a decent starting point. Quote Link to comment Share on other sites More sharing options...
Ryan21 Posted February 14, 2021 Author Report Share Posted February 14, 2021 Thank you. I found that basemap. In the ecu layout it says there is only two triggers being used. The k series has 3 trigger type sensors, 2 cam and 1 crank. How would I know which cam sensor to use? Or is there a way to use both? Quote Link to comment Share on other sites More sharing options...
Adamw Posted February 14, 2021 Report Share Posted February 14, 2021 The base map shows exhaust cam connected to trigger 2 and inlet cam connected to DI1. There is wiring info in the help file, I will attach below. If you are using a factory loom you will need the relay for the vtec solenoid as shown in the diagram below (since factory ecu switches 12V side), if you are making your own loom then you can do it without the extra relay, connect it direct to an aux output and the other side of the solenoid to +12V. Oh, be aware also, Im pretty sure the K24 crank sensor pinout is different than the K20, so you need to research that yourself. Ryan21 and HaveYouSeenAWizardSleep 2 Quote Link to comment Share on other sites More sharing options...
Ryan21 Posted February 14, 2021 Author Report Share Posted February 14, 2021 Thank you so much! Quote Link to comment Share on other sites More sharing options...
Hyperblade Posted February 15, 2021 Report Share Posted February 15, 2021 On 2/15/2021 at 9:34 AM, Adamw said: Oh, be aware also, Im pretty sure the K24 crank sensor pinout is different than the K20, so you need to research that yourself. That's correct they are different. Also the K20a from the Accord Euro R (CL7) runs the K24 connector and pinout, I would guess the FD2 K20a might also as it's based of the CL7 engine originally. Taken from the Haltech K20 page... Ryan21 1 Quote Link to comment Share on other sites More sharing options...
Ryan21 Posted February 24 Author Report Share Posted February 24 On 2/14/2021 at 3:34 PM, Adamw said: The base map shows exhaust cam connected to trigger 2 and inlet cam connected to DI1. There is wiring info in the help file, I will attach below. If you are using a factory loom you will need the relay for the vtec solenoid as shown in the diagram below (since factory ecu switches 12V side), if you are making your own loom then you can do it without the extra relay, connect it direct to an aux output and the other side of the solenoid to +12V. Oh, be aware also, Im pretty sure the K24 crank sensor pinout is different than the K20, so you need to research that yourself. Hey Adam, It has been a while lol. I hope you are doing well. I'm NOT using a factory loom, so I have a question about wiring the VTEC solenoid without the additional relay as you stated above. Did you mean to wire that connector as seen in the image on the left? The factory connector is in the center and the factory Honda diagram is on the right. It looks like it just needs a switched power and ground. I think I'm a little confused. Quote Link to comment Share on other sites More sharing options...
aerace_fab Posted February 24 Report Share Posted February 24 wire it like the picture on the left. Ryan21 1 Quote Link to comment Share on other sites More sharing options...
Ryan21 Posted February 25 Author Report Share Posted February 25 Thank you! I assume the pin locations are correct? Or should I swap the 12V and ECU Aux output? Quote Link to comment Share on other sites More sharing options...
Adamw Posted February 25 Report Share Posted February 25 They are not polarity sensitive, 12V can go to either pin. The 12V supply needs to be ignition switched. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.