goyo Posted August 31, 2018 Report Share Posted August 31, 2018 Hola de nuevo, ya he logrado encender el motor, pero no sé dónde tengo que conectar el AFR y el turbo solenoide, alguien puede ayudarme. También quiero poner el vtec a funcionar, ¿es solo paletas, algo de información? un saludo Goyo Quote Link to comment Share on other sites More sharing options...
Adamw Posted August 31, 2018 Report Share Posted August 31, 2018 I thought on the M50B25Tu the vanos was just an on/off type, not fully variable? Can you confirm. The wideband can be connected to the expansion loom (easiest option) or you can connect it to one of the unused analog inputs on the main connector. Pin 41 (AN Volt 6) is one option, this was for the MAF originally. Pin 13 (AN Volt 3) is another, this was originally for the narrowband oxy sensor. Quote Link to comment Share on other sites More sharing options...
integrale8v Posted September 1, 2018 Report Share Posted September 1, 2018 M50b25tu is on/off vanos. M52b25tu is variable vanos (and ethrottle) Quote Link to comment Share on other sites More sharing options...
goyo Posted September 2, 2018 Author Report Share Posted September 2, 2018 El 1/9/2018 a la 1:43, Adamw dijo: Pensé en el M50B25Tu que los vanos solo eran un tipo de encendido / apagado, no totalmente variables. Puedes confirmar. La banda ancha se puede conectar al telar de expansión o se puede conectar a una de las entradas analógicas no utilizadas en el conector principal. El pin 41 (AN Volt 6) es una opción, para el MAF. El pin 13 (AN Volt 3) es otro, para el oxi sensor de banda estrecha. Hola Adam, gracias por responder. El Vanos no es variable, está ENCENDIDO / APAGADO. Puedo conectar Wideband en el pin 41 y pin 13? ¿Es necesario configurar? un saludo Goyo Quote Link to comment Share on other sites More sharing options...
Adamw Posted September 2, 2018 Report Share Posted September 2, 2018 3 minutes ago, goyo said: Hola Adam, gracias por responder. El Vanos no es variable, está ENCENDIDO / APAGADO. Puedo conectar Wideband en el pin 41 y pin 13? ¿Es necesario configurar? un saludo Goyo Yes, you can use either pin 41 or 13, you may also need to connect the wideband ground to the ecu depending on whether your wideband has a separate analog ground. Yes you will need to set either AN Volt 3 or 6 to function "Lambda 1" and assign correct calibration. If you are using our E36 plug-in ECU then the vanos should already be set up on Aux 3. Quote Link to comment Share on other sites More sharing options...
goyo Posted September 2, 2018 Author Report Share Posted September 2, 2018 Hace 4 minutos, Adamw dijo: Sí, puede usar el pin 41 o 13, también puede necesitar conectar la tierra de banda ancha al igual que su banda ancha tiene una tierra analógica separada. Sí, configurar configurar ANOTE Vots 3 o 6 para que funcionen "Lambda 1" y asignar la calibración correcta. Si está utilizando nuestra ECU enchufable E36, entonces los varones y tú estarás configurados en Aux 3. If I am using the ecu bmw, I just checked the Vanos is activated, I will connect the wideband and try, thanks for answering so fast. a greeting Goyo Quote Link to comment Share on other sites More sharing options...
goyo Posted September 2, 2018 Author Report Share Posted September 2, 2018 another question, to be able to activate and deactivate the antilag as I have to do? I have installed this motor to open and close the throttle, it works with positive and negative, how can I run 2 seconds and then invert positive and negative to close? I await your response Adamw a greeting Goyo Quote Link to comment Share on other sites More sharing options...
Adamw Posted September 2, 2018 Report Share Posted September 2, 2018 Probably the easiest option is 2 separate relays, or a single DPDT relay. Quote Link to comment Share on other sites More sharing options...
goyo Posted September 2, 2018 Author Report Share Posted September 2, 2018 ok, and why do we have to give the input signal to activate the antilag? Quote Link to comment Share on other sites More sharing options...
Adamw Posted September 2, 2018 Report Share Posted September 2, 2018 2 minutes ago, goyo said: ok, and why do we have to give the input signal to activate the antilag? Sorry, I dont understand your question? Quote Link to comment Share on other sites More sharing options...
goyo Posted September 2, 2018 Author Report Share Posted September 2, 2018 I want to put a switch to activate and deactivate the antilag, and I do not know where I have to connect the cable to the ECU Quote Link to comment Share on other sites More sharing options...
Adamw Posted September 2, 2018 Report Share Posted September 2, 2018 Ok, any digital input. You can use DI5 on pin 81 or DI4 on pin 57, these were originally only used for automatic transmission cars. Your switch can be to ground or to +12V, doesnt matter. Quote Link to comment Share on other sites More sharing options...
goyo Posted September 2, 2018 Author Report Share Posted September 2, 2018 ok, and how do I have to name or assign it to do this function? Quote Link to comment Share on other sites More sharing options...
Simon Posted September 3, 2018 Report Share Posted September 3, 2018 It would be assigned as a GP input. You can then label as Anti lag switch. Quote Link to comment Share on other sites More sharing options...
goyo Posted September 3, 2018 Author Report Share Posted September 3, 2018 12 hours ago, Simon said: It would be assigned as a GP input. You can then label as Anti lag switch. Ok Thank Quote Link to comment Share on other sites More sharing options...
goyo Posted September 3, 2018 Author Report Share Posted September 3, 2018 Can the polarity be reversed in 2 outputs for the turbo solenoid? that when I activate the antilag of 12 +/- current and when I stop the antilag send 12 - / +, using 2 outputs for the solenoid. Quote Link to comment Share on other sites More sharing options...
goyo Posted September 4, 2018 Author Report Share Posted September 4, 2018 On 9/2/2018 at 11:53 AM, Adamw said: Probably the easiest option is 2 separate relays, or a single DPDT relay. Could 2 input be made with 2 timed outputs and polarity change? I know that it can be done in some way by managing the ecu, because I've seen it done. Quote Link to comment Share on other sites More sharing options...
Adamw Posted September 6, 2018 Report Share Posted September 6, 2018 On 9/5/2018 at 1:56 AM, goyo said: Could 2 input be made with 2 timed outputs and polarity change? I know that it can be done in some way by managing the ecu, because I've seen it done. No, our plug-in ecu doesnt have any high-side drives or H-bridge type functionality, the aux outputs can only switch to ground. Quote Link to comment Share on other sites More sharing options...
goyo Posted September 7, 2018 Author Report Share Posted September 7, 2018 On 6/9/2018 at 4:13, Adamw said: No, nuestro plug-in ecu no tiene ninguna unidad de lado alto o la funcionalidad de tipo H-bridge, las salidas auxiliares solo pueden cambiar a tierra. ok thanks Quote Link to comment Share on other sites More sharing options...
goyo Posted September 10, 2018 Author Report Share Posted September 10, 2018 On 9/6/2018 at 4:13 AM, Adamw said: No, our plug-in ecu doesnt have any high-side drives or H-bridge type functionality, the aux outputs can only switch to ground. Hello Adamw What can I do when I activate the antilag to have a timed exit and when I deactivate having another timed exit? I already know how to invert the polarity, with 2 relays. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.