orlando bello Posted April 21, 2020 Report Share Posted April 21, 2020 Link Monsson G4X on a Toyota 4efte 24+1 trigger dizzy Trigger error headage from 1000 rpm and below have play with threshold voltage tigger 1 and 2 no luck engine fire up fine and asoon a trigger error show engine shut down and if you crank it over with ignition on there is no trigger reading .have to turn switch back of and on for the engine to fire up and ecu to the latest firmware. Quote Link to comment Share on other sites More sharing options...
Adamw Posted April 21, 2020 Report Share Posted April 21, 2020 Triggerscope and tune please. Quote Link to comment Share on other sites More sharing options...
orlando bello Posted April 22, 2020 Author Report Share Posted April 22, 2020 TriggerScopeLog.zip Quote Link to comment Share on other sites More sharing options...
Adamw Posted April 22, 2020 Report Share Posted April 22, 2020 Ok, scope doesnt look too bad in that. Can I get a copy of the map too please. Can you explain how/when the problem occurs better. Quote Link to comment Share on other sites More sharing options...
orlando bello Posted April 22, 2020 Author Report Share Posted April 22, 2020 Been trying to upload the map but its dont compress that low .until now The engine fire up fine and when idle it dies when I look in the runtime there is a trigger error reported when engine quit. Ignition switch still on i crank again no rpm signal. I have to turn the ignition switch back off completely and back on to start the engine will fire up again .notice if the engine idle abov 1500rpm it won't quite. Or shut down .I have try many threshold voltage with no luck jet. I do have a g4+ atom as well no issues at all .even with 1 or 2 trigger errors. Quote Link to comment Share on other sites More sharing options...
Adamw Posted April 22, 2020 Report Share Posted April 22, 2020 The G4X is definitely more fussy when it sees a trigger error, it will shut the engine down if it doesnt get a valid sync quickly. For the common Toyota dizzys you need very low arming thresholds at low RPM so it kind of sounds like that is what it is not happy about. Set both trig 1 & 2 like this: Quote Link to comment Share on other sites More sharing options...
orlando bello Posted April 22, 2020 Author Report Share Posted April 22, 2020 14 minutes ago, Adamw said: The G4X is definitely more fussy when it sees a trigger error, it will shut the engine down if it doesnt get a valid sync quickly. For the common Toyota dizzys you need very low arming thresholds at low RPM so it kind of sounds like that is what it is not happy about. Set both trig 1 & 2 like this: Adam I will try that out of my head I think I have try those values but will try again.this is the first one and I have 2 more Toyota to do I hope there is a solution for this situation. Simon at link ecu have the map maybe he can e-mail it to you .if you want to take a look . Adam those value I have start with from a Mr2 plug in ecu.that mean I should have the same issue still.not at the shop now any more. Quote Link to comment Share on other sites More sharing options...
Simon Posted April 22, 2020 Report Share Posted April 22, 2020 From what I can see it looks to loose triggers but suddenly. Arvin 4efte.pclx 4e idle and shut down.llgx Then in the log of it cranking and no start it is getting no triggers again. Quote Link to comment Share on other sites More sharing options...
orlando bello Posted April 22, 2020 Author Report Share Posted April 22, 2020 Simon thanks to for the post .what you guys think for a solution as I have 2 more Toyota to do this week all same dizzy. Quote Link to comment Share on other sites More sharing options...
Adamw Posted April 22, 2020 Report Share Posted April 22, 2020 In the map Simon attached the trig 1 arming threshold looks similar to my suggestion, but trigger 2 is quite a bit higher. I think that is the first thing I would try. Otherwise Im thinking there is a bad connection somewhere. Quote Link to comment Share on other sites More sharing options...
orlando bello Posted April 23, 2020 Author Report Share Posted April 23, 2020 Would like to say thanks to David link sort out the trigger error counter issue .notice big difference between the link g4+ voltage threshold on the Toyota dizzy.did not like much that when error counter is present that the engine shut down and you have to turn ignition switch all the way of for the engine to fire up again. Quote Link to comment Share on other sites More sharing options...
Adamw Posted April 23, 2020 Report Share Posted April 23, 2020 So what solved it? Just reducing the trigger 2 arming voltage? Quote Link to comment Share on other sites More sharing options...
orlando bello Posted April 23, 2020 Author Report Share Posted April 23, 2020 Yes Adam its running I was able to do 3 wot pull on dyno to day all nice. The engine shut down again after a wot dyno pull.guess need a bit more work on the threshold voltage. Quote Link to comment Share on other sites More sharing options...
orlando bello Posted April 24, 2020 Author Report Share Posted April 24, 2020 Hello guys Any body have experience this trigger error situation on a Toyota 24+1 dizzy .voltage threshold values from the help file don't work with my current setup voltage are to high dont work. I have try many filters combination and lowering the threshold values from 3000rpm to 0 rpm .car fire up fine but in idle it quit and loose trigger 1.its a G4x monsoon. Any help will be gr8 . Quote Link to comment Share on other sites More sharing options...
Adamw Posted April 24, 2020 Report Share Posted April 24, 2020 Are both trig 1 & 2 set up like below already? Filters should be set on level 1. If you still have problems with the arming thresholds below then you need to get an ocilloscope on to it (or a bigger ecu with built-in scope) and get us a capture of the signals. On 4/22/2020 at 1:32 PM, Adamw said: The G4X is definitely more fussy when it sees a trigger error, it will shut the engine down if it doesnt get a valid sync quickly. For the common Toyota dizzys you need very low arming thresholds at low RPM so it kind of sounds like that is what it is not happy about. Set both trig 1 & 2 like this: Quote Link to comment Share on other sites More sharing options...
orlando bello Posted April 24, 2020 Author Report Share Posted April 24, 2020 Yes Adam they are like the setting .like you mentioned. I have sent a trigger scoop from a link storm in at tech support. Simon or David should have it. Quote Link to comment Share on other sites More sharing options...
orlando bello Posted April 25, 2020 Author Report Share Posted April 25, 2020 Tested a other Dizzy today and still the same situation. Going to chk the voltage tomorrow from the dizzy with a Scoop to and record voltage. And hope for a solution soon. Quote Link to comment Share on other sites More sharing options...
orlando bello Posted May 7, 2020 Author Report Share Posted May 7, 2020 Hello guys I'm back on this topic because it's my second install with the monsoon g4x and have same trigger error issue this time with a 4age 20v 24+1 tooth dizzy.it only happen in idle .have try many threshold voltage and filter combination .even close the air gap of the trigger 1 .have install a g4+ storm for more than 5min in idle not trigger errors at all that only the g4x will shut Down when it captures trigger errors. Andy body else have this situation that is very frustrating. I do have one more monsoon g4x to install and aim 100% sure I will be running in same issue. Need to solve this asap.one more thing I have capture 3 different scoop from the link storm g4+ 0 rpm 1000rpm and 2000rpm and put those threshold values in the g4x still trowing errors. Quote Link to comment Share on other sites More sharing options...
Adamw Posted May 7, 2020 Report Share Posted May 7, 2020 Can you attach the scopes from the G4+ and logs of the G4X trigger error. Quote Link to comment Share on other sites More sharing options...
orlando bello Posted May 7, 2020 Author Report Share Posted May 7, 2020 Hello Adam I can upload any more log or scoop my attachments is full. Quote Link to comment Share on other sites More sharing options...
dx4picco Posted May 7, 2020 Report Share Posted May 7, 2020 you need to use an external host like google drive or others Quote Link to comment Share on other sites More sharing options...
orlando bello Posted May 7, 2020 Author Report Share Posted May 7, 2020 Ok will try thanks Quote Link to comment Share on other sites More sharing options...
Corrado Posted April 7, 2021 Report Share Posted April 7, 2021 Just seeing how you went with this Orlando? Am experiencing similar issues with a distributor setup with a G4x. Quote Link to comment Share on other sites More sharing options...
Adamw Posted April 7, 2021 Report Share Posted April 7, 2021 6 minutes ago, Corrado said: Just seeing how you went with this Orlando? Am experiencing similar issues with a distributor setup with a G4x. Please do a triggerscope and attach that and your tune here. Quote Link to comment Share on other sites More sharing options...
orlando bello Posted April 7, 2021 Author Report Share Posted April 7, 2021 hello guys sofar with the update firmware its been gr8 and also i been using resistor type sparkplugs that have solve many of the triggers issue i have experience in the beginning of the G4x series. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.