TechDave Posted October 3, 2016 Report Share Posted October 3, 2016 (edited) Hi guys, so I've just put up a new release of PCLink and the firmware. Thanks for your patience with this oneYou can grab it from here: http://www.linkecu.com/software-support/pc-link-downloads/PCLink version 5.x.x.3229 (DLL Rev 3189) - 03-10-16New FeaturesBasemap Backup - See Firmware Updater - Basemap Backup for details.Shift + clicking on view close icon closes the view without prompting the user - useful for quickly closing many views.Save Trigger Scope as log file.ChangesImprovements to CAN Setup form.Improvements to Parameter Selection - will now search based on filter selection, table axis selection is now restricted to parameters available to the ECU.When changing a value using a math function, the input is not tested against the bounds of the item it is changing. Note that if the value goes outside of the bounds, it will be set the to the relevant maximum or minimum.FixesUsers can now select more than 25 parameters when adding them to the ECU Logging list.Pasting cells on to a table will always paste from the top left hand corner of the selection.Allocated tables now zero axis as well as table values when prompted.Traction Control tables now update which table is active correctly.G4 basemaps are now able to be upgraded to G4+ by loading them into a G4+ ECU again.Improved performance of CAN Devices form with respect to programming CAN-Lambda Modules on slower computers. Firmware Version 5.6.4.3240 - 20-10-16New FeaturesSupport for Monsoon ECU.FixesKnock and individual cylinder ignition trims did not always operate as expected.NOTE: Critical update for 5.6.0 – 5.6.3 firmware.Firmware Version 5.6.3.3227 - 30-09-16New FeaturesGP Timer can now be reset on a input transition.Gearshift engine cut can now be selected as ignition or fuel.ChangesIdle Ignition Table is now interpolated in 0.1 degree steps.Recalibration for ECU temperature below -10 degrees C.RPM and MAP Limits Ignition Trim range is increased to -20 degrees.Add Toggle switch mode to Traction Control Disable Switch.FixesCorrected modelled fuel equation when BAP is used as load. WARNING: If previously tuned using BAP as load, a retune will be required.When using Group/Staged injection mode with modelled fuel equation the secondary injectors gave 0.2ms pulse when locked-out.Boost Wastegate Duty Trim Table was being corrupted on Link G4+ Force GDI ECUs.Wasted Spark ignition now works on Ford BA XR6 trigger mode.Half sync starting now drives all ignition outputs on Ford BA XR6 trigger mode.Speedo Out now works on Aux 17 - 20.Lock Timing switch now works on DI9 & DI10.Fuel cuts now work if injector duty cycle is 100%.DI5 status is now updated is set to Traction Disable.Lambda Average now includes inputs from CAN-Lambda.Microtech Dash CAN stream now outputs oil and fuel pressure correctly.As always, here's how to update your firmware the best way:If you have any questions or issues please post them in this thread. Edited February 6, 2017 by EngineeringDave JMP, Scott, Adturb and 1 other 4 Quote Link to comment Share on other sites More sharing options...
1320MINI Posted October 4, 2016 Report Share Posted October 4, 2016 Been having issues with the CAN Lambda on a G4+ MINI LINK. Hopefully this will fix it. Quote Link to comment Share on other sites More sharing options...
TechDave Posted October 4, 2016 Author Report Share Posted October 4, 2016 Been having issues with the CAN Lambda on a G4+ MINI LINK. Hopefully this will fix it.What issues? Quote Link to comment Share on other sites More sharing options...
Simon Posted October 4, 2016 Report Share Posted October 4, 2016 Suspect the following fix will be the solution for 1320 MiniLambda Average now includes inputs from CAN-Lambda. Quote Link to comment Share on other sites More sharing options...
Rich RDE Posted October 6, 2016 Report Share Posted October 6, 2016 Been having issues with running some cars when introducing Modeled fuel equation in traditional the Lambda average is not correct and the car will not start at all. Works when in modeled multi blend. Any one else see this? Quote Link to comment Share on other sites More sharing options...
Scott Posted October 7, 2016 Report Share Posted October 7, 2016 Hi Rich, the previous firmware versions have had some issues with Lambda Average not reading correctly, however I'm not aware of any problems in the new 5.6.3.3229 release. If you come across the problem again can you save the 'Modelled' base-map and send to us with a PCLog of the problem occurring? Can you then switch to 'Modelled Multi-Fuel', save the base-map, record another PCLog (of it working) and send all four files to us?Cheers,Scott. Quote Link to comment Share on other sites More sharing options...
Crispin Posted November 11, 2016 Report Share Posted November 11, 2016 I tested the new fuel based gear cut on the dyno. Seems to be working fine Thanks for that function! Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.