Toliski Posted September 6, 2017 Report Share Posted September 6, 2017 Hello guys i just order my Tst205+ with 4bar map for my mr2. It arrives at 20 days!I want to know what i need to be changed to make the COP mod. And Maybe anyone can send me the base map for st205 so i can gen some practice on it? Quote Link to comment Share on other sites More sharing options...
Brad Burnett Posted September 6, 2017 Report Share Posted September 6, 2017 (edited) As far as a base calibration, there is one in the "Base Maps" file that is downloaded with the link software. What needs to be changed, you will have to wire in individual coils and modify the wiring to suit.The pinout for the ecu is also in the help file in the software. Edited September 6, 2017 by Brad Burnett Quote Link to comment Share on other sites More sharing options...
Toliski Posted September 6, 2017 Author Report Share Posted September 6, 2017 As far as a base calibration, there is one in the "Base Maps" file that is downloaded with the link software. What needs to be changed, you will have to wire in individual coils and modify the wiring to suit.The pinout for the ecu is also in the help file in the software.Thank you very much!!! Quote Link to comment Share on other sites More sharing options...
Adzn3k Posted September 9, 2017 Report Share Posted September 9, 2017 I converted my celica st205 recently its pretty straightforward to do, I made my own loom for the 1zz coils, I did have to offset the timing by 360 degrees to get it to run though Quote Link to comment Share on other sites More sharing options...
Toliski Posted September 9, 2017 Author Report Share Posted September 9, 2017 I converted my celica st205 recently its pretty straightforward to do, I made my own loom for the 1zz coils, I did have to offset the timing by 360 degrees to get it to run though Hello Adzn3k.only this change you made for cop or I must to change and other parameters?I have the stock ign system for now but it start to missfire at high boost! It's time for upgrade!Do you tune your Link alone? Quote Link to comment Share on other sites More sharing options...
Adzn3k Posted September 9, 2017 Report Share Posted September 9, 2017 I setup and wired my cop conversion then I set it up in the ecu (dwell tines and so on) got it running and idling then I took the car to be dyno tuned but it wasn't a very good tune and I've been trimming the fuel as it was just too rich Quote Link to comment Share on other sites More sharing options...
Toliski Posted September 9, 2017 Author Report Share Posted September 9, 2017 I setup and wired my cop conversion then I set it up in the ecu (dwell tines and so on) got it running and idling then I took the car to be dyno tuned but it wasn't a very good tune and I've been trimming the fuel as it was just too rich Have you any diagram for wiring or a forum threat, if you follow one? Quote Link to comment Share on other sites More sharing options...
MGV101 Posted September 13, 2017 Report Share Posted September 13, 2017 (edited) Look for pinouts on the 1zz coil.I connected the +12 to the original coil power supply coming out from the fuse box, -ve to a grounding point on the engine block itself, and IGT (trigger) to the appropriate ignition outputs from the ECU according to cylinder number. It's nothing complicated, the ECU settings will handle the rest. The IGF pin on the coil is not used. Edited September 13, 2017 by MGV101 Toliski 1 Quote Link to comment Share on other sites More sharing options...
Toliski Posted September 13, 2017 Author Report Share Posted September 13, 2017 Look for pinouts on the 1zz coil.I connected the +12 to the original coil power supply coming out from the fuse box, -ve to a grounding point on the engine block itself, and IGT (trigger) to the appropriate ignition outputs from the ECU according to cylinder number. It's nothing complicated, the ECU settings will handle the rest. The IGF pin on the coil is not used. Thank you very much! You are a life saver!!!Can you send me a map of you to copy just the settings?I found one before a couple of days but i want to be sure. Quote Link to comment Share on other sites More sharing options...
MGV101 Posted September 15, 2017 Report Share Posted September 15, 2017 Are you just switching to COP only or have you also replaced the distributor with crank and cam sensors?If COP only, it should be as simple as switching ignition mode to direct spark and setting the correct dwell time for your coils once everything is wired up correctly.As mentioned by Adzn3k, you might also need to advance the timing by 360 degrees if the coils are firing on the wrong stroke (you can hear the mixture burning in the exhaust while being ignited on the exhaust stroke).One more thing to noted. As the G4+ will use ignition drive 1, 2, 3, 4 to control the coils, purge originally assigned to ignition drive 2 will no longer function and you'll need to reassign the function to another output. I don't have a charcoal canister so it doesn't matter to me. Quote Link to comment Share on other sites More sharing options...
Toliski Posted November 15, 2017 Author Report Share Posted November 15, 2017 Just COP guys. Today i try to make the Cop thing. Well jus finish alla harness and try to put the settings to ECU. Ignition main changed to direct spark. base timming advanced by 360 degrees dwell times changed. Ignition1 drive is at ignition. Ignition2 drive is at purge and its Locked Ignition 3-4 its OFF and Locked am i making any mistake here? Cop.pclr Quote Link to comment Share on other sites More sharing options...
MGV101 Posted November 15, 2017 Report Share Posted November 15, 2017 Yes the software is a little confusing here. Once you switch to direct spark it actually sets ign 1 to 4 as ignition output and locks it. Whatever you see in the settings does not matter and will be ignored. For the peace of mind, you can switch ignition main back to distributor and that will unlock ign 2 to 4 and manually set it as ignition then revert ignition main back to direct spark again. Quote Link to comment Share on other sites More sharing options...
Toliski Posted November 15, 2017 Author Report Share Posted November 15, 2017 48 minutes ago, MGV101 said: Yes the software is a little confusing here. Once you switch to direct spark it actually sets ign 1 to 4 as ignition output and locks it. Whatever you see in the settings does not matter and will be ignored. For the peace of mind, you can switch ignition main back to distributor and that will unlock ign 2 to 4 and manually set it as ignition then revert ignition main back to direct spark again. ok i try it. thanks a lot Quote Link to comment Share on other sites More sharing options...
Adamw Posted November 15, 2017 Report Share Posted November 15, 2017 Ignition drives only get assigned when loaded into an ecu. Load your map, store, then power cycle. Drives will then be assigned correctly according to your ignition mode. Toliski 1 Quote Link to comment Share on other sites More sharing options...
Toliski Posted November 20, 2017 Author Report Share Posted November 20, 2017 Guys i have set my ignition timing with timing light when i was on standard 3s coil. Now i made the COP trick. I unplug my standard coil but i don't move the distributor from it position. I must to check again the timing? and if yes how I doing this with COP Quote Link to comment Share on other sites More sharing options...
Simon Posted November 20, 2017 Report Share Posted November 20, 2017 Yes timing should be checked. Jut put a HT lead between the coil and plug to allow a timing light to be clipped on. Toliski 1 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.