Fence Posted January 31, 2018 Report Share Posted January 31, 2018 Hi Guys, Would anybody happen to have a base map for n14 Gti-r Pulsar? If so possible to source. Thanks Quote Link to comment Share on other sites More sharing options...
Adamw Posted January 31, 2018 Report Share Posted January 31, 2018 If nobody else comes up with anything useful after a day or 2 then I think I know this model well enough to knock up a basic starting point. Basically, I would start with our S13 or S14 map, change the ignition set up to suit the distributor and change the fuel map to TP to suit the ITB's. @Ducie54 may also be some help. Quote Link to comment Share on other sites More sharing options...
Ducie54 Posted January 31, 2018 Report Share Posted January 31, 2018 I have a few. But they are all for G4 traditional setups. Send me an email at [email protected] and I'll give you a starting point. May need tweaking as they had big injectors. Quote Link to comment Share on other sites More sharing options...
Fence Posted January 31, 2018 Author Report Share Posted January 31, 2018 Thanks Adam, I did have similar idea working off the s13, being Quad TB i feel may be small challenge. IAT is located After TMIC back side of plenium, before 1st TBI. Hope this will suit. Ducie54, i have emailed you, any base on g4 can give certainly me indications. I appreciate both your help guys. Quote Link to comment Share on other sites More sharing options...
Ducie54 Posted February 1, 2018 Report Share Posted February 1, 2018 I sent you a file it was using stock turbo and 700cc sard injectors. Let us know how u go. Quote Link to comment Share on other sites More sharing options...
Fence Posted February 17, 2018 Author Report Share Posted February 17, 2018 Hi guys, Ive got it started but I cannot change the values in trigger calibrate, When selecting " set base timing" . Also I have put Pin 16 (gtir MAF sensor Signal) into position pin 15 for AN Temp 2. Fair to assume its fine?. so far it is. Thanks Quote Link to comment Share on other sites More sharing options...
ClintBHP Posted February 17, 2018 Report Share Posted February 17, 2018 You have to hit enter after changing them Fence and AbbeyMS 2 Quote Link to comment Share on other sites More sharing options...
Fence Posted February 18, 2018 Author Report Share Posted February 18, 2018 Ofcourse it was that simple. Thank you kindly. Quote Link to comment Share on other sites More sharing options...
Fence Posted February 20, 2018 Author Report Share Posted February 20, 2018 (edited) I was doing rather well I thought up until now. Used S15 94 -02 jumpers on ecu G4 + then started on s15 base tune, set distributor , set triggers, calibrated base timing and was idling fine, I installed 1000cc injectors and used the resistor delete and set main Fuel to 45 percent (6MS) to match similar to the 444cc I removed. Started idled almost identical, was rather surprised. Then I changed the IAT sensor type to Delphi, (which it is) after about 40 seconds it decide to die. haven't been able to get started since. Tested injectors, tested changing IAT back, have fuel, No errors or codes bar the oxy sensor . Unfortunately hadn't set up a log. If anybody has the chance to browse over much appreciate. thanks GTi-R Base Tune 3.pclr Log GTIR BASE 3 2018-02-19 9;17;04 pm.llg Log GTIR BASE 3 2 trys.llg Edited February 20, 2018 by Fence Maybe an obvious reason in my config also attatched a log trying to start it Quote Link to comment Share on other sites More sharing options...
Adamw Posted February 20, 2018 Report Share Posted February 20, 2018 I had a very brief look and it mostly looks like everything is working. A master of 6ms sounds a bit stingy for 1000cc inj. Can you try about 10ms, see if it feels any more promising. Quote Link to comment Share on other sites More sharing options...
Brad Burnett Posted February 20, 2018 Report Share Posted February 20, 2018 I will normally adjust the master fuel while paying attention to the lambda at idle. I don't normally try to use the percentage change as it is not always correct. Quote Link to comment Share on other sites More sharing options...
Fence Posted February 20, 2018 Author Report Share Posted February 20, 2018 Master originally was 14ms and I did drop 1ms until It idled at 6ms ok which was my math also of 444cc . I will try 10ms. Also I will check the plugs, I wouldn' have they would be to wet to fire however that may simply be the case. Thanks guys Quote Link to comment Share on other sites More sharing options...
ClintBHP Posted February 20, 2018 Report Share Posted February 20, 2018 Your battery voltage is only 9v while cranking. You have over 5ms of injection pulse while trying to crank, on 1000cc's I would expect that to be closer to 2-3ms almost certainly flooded the engine while having too much fuel and limited spark. Are you sure your injector dead times are correct for them new injectors ? Sort your battery voltage out and check the dead-times, remove the fuel pump relay, turn the engine over and adjust the master fuel until the pulse is around 2.5ms and go from there. Quote Link to comment Share on other sites More sharing options...
Fence Posted February 21, 2018 Author Report Share Posted February 21, 2018 (edited) Ok guys check this filthy log out. Its bad I know. then after that escapade of sputtering. It turns out a loose wire on in the loom. Tried 10ms as a starting point last night. Was to rich. I moved loom and ecu and it fired. Something that's loose wont allow spark. maybe power transistor? (ignition amplifier). I manipulated loom until I could start car. Master Fuel run idled better at 7ms . 4ms lowest on master was too low. Log 2018-02-21 20;24;35 pm.llg went to start 20;08 pm.llg Well i spent hours going over loom. All grounds are fine. Everything had continuity . I suspect its a pin or break in wire when on slight angle. This is going to be a fun one tracking it down. I'll update as soon as I know. Thanks guys for your help. . Edited February 21, 2018 by Fence Update Quote Link to comment Share on other sites More sharing options...
Gtir Posted May 9, 2021 Report Share Posted May 9, 2021 Hi Everyone. Same issue would love a base map to start a gtir. Stock injectors MAP sensor. Pretty keen to just fire the motor and do basic checks before we take it to the dyno. Quote Link to comment Share on other sites More sharing options...
Adamw Posted May 9, 2021 Report Share Posted May 9, 2021 There is a GTiR map 6 posts up. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.