Simon Posted October 31, 2019 Report Share Posted October 31, 2019 Hi Greg that likely going to have to be serial. Its pre 10000 serial which is our usual cut off. But if you want to try can there is no harm it will work or not. Quote Link to comment Share on other sites More sharing options...
bsh Posted October 31, 2019 Report Share Posted October 31, 2019 13 hours ago, Adamw said: Hi Ben, I will PM you some instructions. Edit - added later: Note you can also connect the dash via serial and it will work without the CAN mod, this is just a bit painful though as you cant have the laptop and dash connected at the same time - you have to unplug the dash when you want to tune. Thanks:) Quote Link to comment Share on other sites More sharing options...
roarpw Posted March 8, 2021 Report Share Posted March 8, 2021 Hi there, sorry to rehash an old topic... Is there a way to program the CAN protocol to enable an AIM mxs Strada to display a temp value that's been set via an Volt with a pull up resistor? Quote Link to comment Share on other sites More sharing options...
Adamw Posted March 9, 2021 Report Share Posted March 9, 2021 Should be able to add it onto the end of the generic stream. If you attach your map and your dash config I will have a go. Quote Link to comment Share on other sites More sharing options...
BrettS1532 Posted April 26, 2021 Report Share Posted April 26, 2021 Hey all, im having the same issues. ECU - Vi-pec V44 plug in for skyline serial 11101 Dash - link mxg strada street edition. Im having issues with the communication between the two of them currently. i have gotten the dash to display a couple of things from the ecu, water temp is showing 280 degree but it couldnt be much above 30degree (C) and rpm is stagnant at 2k on the dash regardless of engine speed. attached is the dash config file and a screen shot of the setup vipec side. any help would be EXTREMELY appreciated!! MXG 1.2 Strada link .zconfig Quote Link to comment Share on other sites More sharing options...
paulr33 Posted April 27, 2021 Report Share Posted April 27, 2021 Try just 1 channel at a time and get that working then try all channels. I.e just do one of the water temps and see what the value is. From memory the v44 has a temp offset of -50 so any value in the CAN packet is offset by 50deg. Can you do “math channels” on your dash to -50 from the value ? Quote Link to comment Share on other sites More sharing options...
Adamw Posted April 27, 2021 Report Share Posted April 27, 2021 15 hours ago, BrettS1532 said: Hey all, im having the same issues. ECU - Vi-pec V44 plug in for skyline serial 11101 Dash - link mxg strada street edition. Im having issues with the communication between the two of them currently. i have gotten the dash to display a couple of things from the ecu, water temp is showing 280 degree but it couldnt be much above 30degree (C) and rpm is stagnant at 2k on the dash regardless of engine speed. attached is the dash config file and a screen shot of the setup vipec side. any help would be EXTREMELY appreciated!! MXG 1.2 Strada link .zconfig 609 kB · 0 downloads That set up in the ecu doesnt look like the generic dash stream. Highlight channel 1 again and click load, then choose the generic dash.lcc file. It should look something like below when correct. Quote Link to comment Share on other sites More sharing options...
yorl Posted May 10, 2021 Report Share Posted May 10, 2021 On 10/31/2019 at 7:37 AM, Adamw said: Hi Ben, I will PM you some instructions. Edit - added later: Note you can also connect the dash via serial and it will work without the CAN mod, this is just a bit painful though as you cant have the laptop and dash connected at the same time - you have to unplug the dash when you want to tune. Hello! Any chance you could forward those instructions as well? I just found out today mine is not CAN friendly when I went to plug in the dash... Thanks Quote Link to comment Share on other sites More sharing options...
Adamw Posted May 10, 2021 Report Share Posted May 10, 2021 What specific model ECU do you have? Also, what is the serial number? Quote Link to comment Share on other sites More sharing options...
yorl Posted May 11, 2021 Report Share Posted May 11, 2021 9 hours ago, Adamw said: What specific model ECU do you have? Also, what is the serial number? It's a V44, serial 5326 Quote Link to comment Share on other sites More sharing options...
Adamw Posted May 11, 2021 Report Share Posted May 11, 2021 I have PM'd you info. Quote Link to comment Share on other sites More sharing options...
yorl Posted May 11, 2021 Report Share Posted May 11, 2021 2 hours ago, Adamw said: I have PM'd you info. Got it! I just modified the ECU as per the instructions, but I'm having problems displaying anything on my dash. It's not an AIM, so I will open another thread. Quote Link to comment Share on other sites More sharing options...
Kristian Egeland Posted March 14, 2022 Report Share Posted March 14, 2022 How to do the hardware upgrade for v88 for serial numbers under 10000? I have two v88 I would like to use to connect to aim mxl dash. Quote Link to comment Share on other sites More sharing options...
Adamw Posted March 14, 2022 Report Share Posted March 14, 2022 6 hours ago, Kristian Egeland said: How to do the hardware upgrade for v88 for serial numbers under 10000? I have two v88 I would like to use to connect to aim mxl dash. Are they wire-in silver boxes? Quote Link to comment Share on other sites More sharing options...
Kristian Egeland Posted March 15, 2022 Report Share Posted March 15, 2022 (edited) 22 hours ago, Adamw said: Are they wire-in silver boxes? Mm, not really sure what you mean by wire-in, but yes Silver boxes. One has #8302 and the other one is #40xx. From what I can find out there has to be done an upgrade to use Can for an easy connection to AIM mxl dash? I have a guy that does circuitboard soldering. I live in Norway, so dont want to send around the world if I dont have to. Edited March 15, 2022 by Kristian Egeland Quote Link to comment Share on other sites More sharing options...
Kristian Egeland Posted March 22, 2022 Report Share Posted March 22, 2022 @Adamw is it possible to get instructions on how to do the CAN upgrade? Quote Link to comment Share on other sites More sharing options...
Adamw Posted March 23, 2022 Report Share Posted March 23, 2022 What ecu do you have? Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.