Jump to content

remski2

Members
 View Profile  See their activity

  • Posts

    197

  • Joined

  • Last visited

  • Days Won

    5

 Content Type 

Posts posted by remski2

  1. VVTI DC question.

    in Engine Tuning

    Posted

    Hi.

    Got a question about VVT DC... its constantly 5%. (idle, start)

    RPM Lockout is 1500 and ECT Lockout is 147F.. 

    Yet right after cold start it jumps to 5%. 

    I dont think its reading it off the VVTi table as that value would drop down with the rpm dropping after the warm-up period... 

    Forgot to add.. Vipec i88 with 5.6.8.3669 software.

     

     

    Thanks

    Remski

    avcs.png

  14. 2007 JDM FORESTER STI WRX104+ Pnp

    in G4x

    Posted

    Hi.

    Your knock needs to be tuned first.. to see if this was real knock. 

    I wouldnt be going around and doing pulls on untuned knock/ignition. This is a recipe for a new iag900 block.

    Either take it to a tuner or take some courses.

     

    Also if you fixed your idle.. post what fixed it.. it might help another guy..

     

    to reduce knock you'd usually remove timing or add fuel or both.. or look at you AVCS.

    Remski

     

    Also.. you went from 6500 to 7700 so either you have trigger issues or your clutch slipped.

  16. 2007 JDM FORESTER STI WRX104+ Pnp

    in G4x

    Posted

    You hitting an ignition cut mid of your pull... 

    You are close to MAP limit but it doesnt show it triggered.. 

    2nd thing.. your knock.. 

    3rd.. you have warm up enrichment on while at normal operating temps.. add that to fuel and zero out your operating range.

    Unless there is another reason to have it on...

     

    my2c.

  17. 2007 JDM FORESTER STI WRX104+ Pnp

    in G4x

    Posted

    I have 272 GSC cams and I idle at 1100.. so bump your idle speed.

    I'd copy the E-throttle PID settings from the base map. 

    Copy your Idle ignition control PID settings from the base map as well. 

    See where that gets you...

    If that doesnt work switch to Open loop idle control and go from there. 

     

    Hope this helps.

  18. Wrx throttle body slow to close

    in G4x

    Posted

    I just compared it to mine.. 05 sti pedal.. and mine runs at ~4.6V when at 100% TP..  ~1.0V at Idle (7% TP)

    Not sure how much that would differ between 05 and 06.. and how much of an impact it would have.. but something that caught my eye..

     

  21. need help with evo log

    in G4+

    Posted

    An volt2 is your MAP sensor.. 

    You probably disconnected the sensor and had the ignition switch on.

    Reset the code and see if it shows up. (check for loose connection)

     

    FYI...

    Also.. as per your log.. ECU is seeing some knock..

  22. Sensor Question.

    in G4x

    Posted

    3 wire back into your Prosport gauge might be tricky.. 

    You will need to check if both sensors output the same voltage for given pressure. 

    Maybe it would be easier to send output from the ECU ??? but I havent figured how to do it. 

  23. Evo 8 grenades on the dyno

    in G4+

    Posted

    I dont think it looks like it moved. If you look close you will see 2 half round marks.. those would be the 2 times the timing was changed and bolt was tightened. 

    If it moved you would not have the mark in the middle, as it would slide from right to left.

    But you clearly see that half way it was tightened again thus leaving the mark of the edge of the bolt. 

    Once you remove the bolt you will probably see the 3rd half round mark.. 

    That would tell you that the bolt was tightened in place and didnt move. 

     

    my2c

  24. Sensor Question.

    in G4x

    Posted

    Well.. put a multimeter on the sensor and see what voltage you get.

    Based on that you can create a CAL table and scale it.. 

    "should be" linear.. 

    I am feeding my Defi gauges into my Link.. 

    Read somewhere that the gauges and ecu have to be grounded together in the same place for reliable readout...  ( and thats how I run it) 

×
×
  • Create New...