CamB Posted September 23, 2016 Report Share Posted September 23, 2016 Just registering interest in (giving encouragement on!) the documentation and code. Would like to give this a go I think. Quote Link to comment Share on other sites More sharing options...
Marty Posted September 23, 2016 Report Share Posted September 23, 2016 I think this would work. You could send out the 'Generic Dash' CAN stream, as this contains most of the data the KMS dash is capable of receiving. You would then re-transmit the data to the KMS after some maths.We have just finished adding G4+/iSeries support for another good value dash manufactured by Microtech. There is talk of them making a mode in the dash to support the 'Generic dash' CAN stream, this would mean the dash could work with the V44/V88 and G4 ECUs.http://microtechefi.com/product/ltc-display-dash/One other good value dash which already has support for the V44/V88 and GG4 ECUs is the Toucan.http://www.jti.uk.com/toucan-available-for-link-g4g4-and-vi-pec/ Hi ScottHow does the ecu connect to the microtech dash ? Quote Link to comment Share on other sites More sharing options...
paulr33 Posted September 24, 2016 Report Share Posted September 24, 2016 Yeah happy to release the code and write it up, just need to finish building. Car in storage for two months as we rebuild our garage then I can finish it Quote Link to comment Share on other sites More sharing options...
Scott Posted September 26, 2016 Report Share Posted September 26, 2016 Hi ScottHow does the ecu connect to the microtech dash ?The Link G4+ ECU talks to the Microtech dash over the CAN bus. We have some setup instructions for the ECU under PCLink Help > G4+ ECU Tuning Functions > CAN > Device Specific CAN Information.Scott Marty 1 Quote Link to comment Share on other sites More sharing options...
paulr33 Posted October 14, 2016 Report Share Posted October 14, 2016 Haven't forgotten about this, car still in storage for about another month CamB and Locknar 2 Quote Link to comment Share on other sites More sharing options...
paulr33 Posted October 26, 2016 Report Share Posted October 26, 2016 fyi another product that looks alright, looks like the KMS displayhttp://lancerregister.com/showthread.php?t=528000 Quote Link to comment Share on other sites More sharing options...
Scott Posted October 26, 2016 Report Share Posted October 26, 2016 I like the look of the Plex SDM500. Quote Link to comment Share on other sites More sharing options...
josey Posted December 21, 2016 Report Share Posted December 21, 2016 guys,did you try to run OEM dash with arduino?i have 2006 ford with CAN dash, have some device that run my dash, VIPEC - RS232- device - CAN - DASHRPM and ECT, but we cant get speed to work correctly. Quote Link to comment Share on other sites More sharing options...
paulr33 Posted January 24, 2017 Report Share Posted January 24, 2017 Hi All, I have my car back at home now, out of storage so I'll try and finish this project and document the whole build JMP and davidbek95 2 Quote Link to comment Share on other sites More sharing options...
Scott Posted January 24, 2017 Report Share Posted January 24, 2017 Welcome back paulr33. I'm sure your project will be useful to others in the future.Scott Quote Link to comment Share on other sites More sharing options...
paulr33 Posted February 11, 2017 Report Share Posted February 11, 2017 hi all, hope you are all well. i am in the finishing stages of my can bus display and ive had my local workshop do some work for me (new senors added on). for some reason, my wideband is dead so ill need to spend some time working out why, but i cannot for the life of my make the engine check light go away. ive disabled wideband and also turned off stoich but its still stuck on. any help would be great? logs and tunehttp://www.paulr33.com/evo/help.zipthe only thing i can see in the logs is;AF6 - CE light2 Quote Link to comment Share on other sites More sharing options...
Adamw Posted February 11, 2017 Report Share Posted February 11, 2017 Is there anything shown in the event log? (press E key when live). I only had a very brief look at your log but AN volt 5 is a bit odd, it is a power steering switch but its units display as AFR instead of Volts for some reason. Can you try temporarily turning AN Volt 5 off. Quote Link to comment Share on other sites More sharing options...
paulr33 Posted February 12, 2017 Report Share Posted February 12, 2017 thanks for your help, i will check it soon. the thing that doesnt make sense (if the above is root cause) is that its been like that for about 3 years nowno settings in the tune have changed. ive simply had the workshop run new wires to new unconfigured sensors This is what they have done; · Connect orange wire from Knock controller in globebox to pin 63 (AUX 3) on Vipec ECU loom· Connect green wire from oil temp sensor to pin 96 (An Temp2) on Vipec ECU loom· Connect ANALOG OUT wire from EGT controller sensor to pin 92 (An Volt1) on Vipec loom· Connect blue wire from oil pressure sensor to white wire (An Volt 6) on expansion loom in glovebox i have not yet configured any of those sensors and i also found the air temp (An temp 3) was unpluged, so ive fixed that (air temp working) but the engine light is still stuck onis it because it can see voltage at one of the above sensors and because i havent configured anything its throwing on the engine light? note this is for vipec v44 topboard for evo 9 Quote Link to comment Share on other sites More sharing options...
Adamw Posted February 12, 2017 Report Share Posted February 12, 2017 The analog inputs that are turned off will not throw errors. If AN temp 3 was disconnected then that would generate a fault code. The fault code will remain (and CE light flash) until that fault code is cleared. Quote Link to comment Share on other sites More sharing options...
paulr33 Posted February 12, 2017 Report Share Posted February 12, 2017 Thanks and yeah the engine light was originally on because the air temp sensor was unplugged but I fixed that , confirmed the sensor is working and also did clear error codes but it keeps coming back. the only thing I haven't tried it starting the car and doing a full clear again. Quote Link to comment Share on other sites More sharing options...
Adamw Posted February 12, 2017 Report Share Posted February 12, 2017 also did clear error codes but it keeps coming back.What keeps coming back? The fault code or just the CE light? Quote Link to comment Share on other sites More sharing options...
paulr33 Posted February 12, 2017 Report Share Posted February 12, 2017 The engine check light comes back, even after clearing the errors via "Clear ECU fault codes". ill have to start it and see what it says Quote Link to comment Share on other sites More sharing options...
paulr33 Posted February 13, 2017 Report Share Posted February 13, 2017 double checked a few things today and all the new sensors are working (oil temp, oil pressure and EGT) so that confirms my wiring map outs / pin outs are correct. engine light still stuck on, pressing E during car ON but engine not running reports nothing, if i do clear ecu fault codes the engine light flashes off and back on qiuckly, nothing in event viewer other than it saying ive cleared the errors. "run time stats" all looks good and no issues or anything that would make the engine light come on. ill take it for a drive in an hour or so and do a PC log and see what i can find Quote Link to comment Share on other sites More sharing options...
paulr33 Posted February 13, 2017 Report Share Posted February 13, 2017 ok disregard the engine check light issue, its me being silly and having a brain fartdisregard and all is well, now back onto finishing the canbus display Simon 1 Quote Link to comment Share on other sites More sharing options...
paulr33 Posted February 25, 2017 Report Share Posted February 25, 2017 sorry for delay, had to sort out a few things and fix some bugs, but all working well with my new sensorsneed to finish the documenation (ive done about 1/3 so far) davidbek95, JMP, CamB and 1 other 4 Quote Link to comment Share on other sites More sharing options...
JMP Posted February 27, 2017 Report Share Posted February 27, 2017 Very nice,I've grabbed a 4duino board and attempting to redo my code at the moment, it's a bit of a mess so likely going to start from scratch: http://www.4duino.com/ Quote Link to comment Share on other sites More sharing options...
TheOtherOne Posted March 7, 2017 Report Share Posted March 7, 2017 Loving the idea of this project and is something I've been considering for quite some time, very interesting in your documentation when it's ready Quote Link to comment Share on other sites More sharing options...
paulr33 Posted April 1, 2017 Report Share Posted April 1, 2017 Haven't forgotten, I think I'm about half way through, just juggling work and uni priorities Quote Link to comment Share on other sites More sharing options...
paulr33 Posted June 18, 2017 Report Share Posted June 18, 2017 some final work on this before i glue the case and mount on the apexi standnot sure if i like the R34 GTR style bar graphs on the screen, a little too small, but either way the display is there via touch screenthe software and programming library for the screen is pretty complex and extremely helpful, the video below show briefly how it works davidbek95 1 Quote Link to comment Share on other sites More sharing options...
paulr33 Posted June 24, 2017 Report Share Posted June 24, 2017 CamB 1 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.