G4+

6,730 topics in this forum

1. Idle Load Trim GM TH 400 Automatic Transmission

   By Youngtimer, January 18, 2018
   • 1 reply
   • 330 views
   • 
   • Youngtimer
   • January 18, 2018

2. Some confusion with onboard knock control

   By MGV101, January 18, 2018
   • 3 replies
   • 849 views
   • 
   • Adamw
   • January 18, 2018

3. Denso type ISC valve problem

   By Summer Ng, January 15, 2018
   • 12 replies
   • 1.6k views
   • 
   • Summer Ng
   • January 18, 2018

4. LINK CAN-Lambda Install Help

   By DO1023, January 15, 2018   

   • link
   • g4
   • (and 2 more)

     Tagged with:

     • link
     • g4
     • mr2link
     • canlambda
   • 3 replies
   • 2.6k views
   • 
   • DO1023
   • January 17, 2018

5. G4 extreme unused B Loom

   By ONLYrealRAT, January 16, 2018   

   • unused
   • b loom
   • (and 1 more)

     Tagged with:

     • unused
     • b loom
     • extreme
   • 2 replies
   • 478 views
   • 
   • ONLYrealRAT
   • January 17, 2018

6. crank and cam trigger accuracy

   By nwt1976, January 17, 2018
   • 3 replies
   • 553 views
   • 
   • Adamw
   • January 17, 2018

7. Crank trigger tooth count

   By Josh T, February 27, 2017
   • 18 replies
   • 5.3k views
   • 
   • mapper
   • January 17, 2018

8. CAN dash setup

   By wasted talent, September 30, 2017
   • 16 replies
   • 2.3k views
   • 
   • Simon
   • January 16, 2018

9. IAT installation Subaru V5-V6

   By Dean Govender, December 4, 2017
   • 9 replies
   • 3.1k views
   • 
   • neil brown
   • January 16, 2018

10. Leans out when not moving on fuel map

    By Brad May, January 15, 2018
    • 8 replies
    • 794 views
    • 
    • ClintBHP
    • January 16, 2018

11. crank and cam trigger timing

    By Speedpro, January 16, 2018   

    • trigger timing
    • 2 replies
    • 932 views
    • 
    • Speedpro
    • January 16, 2018

12. Motec PDM to Fury CAN

    By DSORDA, September 12, 2017   

    • can
    • pdm
    • 14 replies
    • 4.3k views
    • 
    • Adamw
    • January 16, 2018

13. 1NZ-FE VVTI Operation

    By Grant Baker, January 15, 2018
    • 2 replies
    • 1k views
    • 
    • Adamw
    • January 16, 2018

14. DBW throttle on link g4+ celica st205

    By Adzn3k, January 9, 2018
    • 13 replies
    • 2.1k views
    • 
    • Zmit
    • January 15, 2018

15. Daihatsu L700 VVti Wiring Problem

    By Summer Ng, January 9, 2018
    • 15 replies
    • 1.7k views
    • 
    • Simon
    • January 15, 2018

16. GM 1Bar Map Sensor Calibration

    By Youngtimer, January 14, 2018
    • 5 replies
    • 1.3k views
    • 
    • ClintBHP
    • January 14, 2018

17. Noisy RPM signal

    By Toliski, January 12, 2018
    • 5 replies
    • 1.3k views
    • 
    • Toliski
    • January 14, 2018

18. launch with speed sensor

    By pitz, January 4, 2018
    • 1 reply
    • 650 views
    • 
    • Simon
    • January 12, 2018

19. Anti Theft set up for Altezza

    By R24, January 4, 2018   

    • anti theft
    • g4+ altezza link
    • (and 1 more)

      Tagged with:

      • anti theft
      • g4+ altezza link
      • 3sge beams
    • 1 reply
    • 1.1k views
    • 
    • Simon
    • January 12, 2018

20. ECU selection trouble

    By MikeR, January 11, 2018   

    • vllink
    • fury
    • 3 replies
    • 656 views
    • 
    • Brad Burnett
    • January 11, 2018

21. Skyline R32 25det, GTRlink.

    By StevenWHK, January 10, 2018   

    • gtrlink gtrlink link g4 skyline r32 25det rb25det
    • nissan
    • 2 replies
    • 592 views
    • 
    • StevenWHK
    • January 11, 2018

22. Pre crank prime

    By Ken Dunkley, January 2, 2018
    • 5 replies
    • 1.1k views
    • 
    • ClintBHP
    • January 10, 2018

23. Toyota Caldina gtt(not starting)

    By Bradz, January 10, 2018   

    • caldina gtt toyota 3sgte
    • 5 replies
    • 1.3k views
    • 
    • ClintBHP
    • January 10, 2018

24. CAN Lambda / Resistor

    By Grant Baker, January 8, 2018
    • 6 replies
    • 2.5k views
    • 
    • ClintBHP
    • January 10, 2018

25. MR2Link unlabelled pins

    By Zmit, January 9, 2018
    • 2 replies
    • 427 views
    • 
    • Zmit
    • January 10, 2018